Attachment 161490 Details for Bug 307162

dmesg.txt

dmesg.txt (text/plain), 22.84 KB, created by tim chappell on 2007-09-03 13:02:03 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: tim chappell

Created: 2007-09-03 13:02:03 UTC

Size: 22.84 KB

patch

obsolete

>Linux version 2.6.22.3-7-default (geeko@buildhost) (gcc version 4.2.1 (SUSE Linux)) #1 SMP 2007/08/20 16:50:09 UTC
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
> BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e9c00 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
> BIOS-e820: 000000007fef0000 - 000000007feff000 (ACPI data)
> BIOS-e820: 000000007feff000 - 000000007ff00000 (ACPI NVS)
> BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
>1150MB HIGHMEM available.
>896MB LOWMEM available.
>found SMP MP-table at 000f6b40
>Entering add_active_range(0, 0, 524016) 0 entries of 256 used
>Zone PFN ranges:
>  DMA             0 ->     4096
>  Normal       4096 ->   229376
>  HighMem    229376 ->   524016
>early_node_map[1] active PFN ranges
>    0:        0 ->   524016
>On node 0 totalpages: 524016
>  DMA zone: 32 pages used for memmap
>  DMA zone: 0 pages reserved
>  DMA zone: 4064 pages, LIFO batch:0
>  Normal zone: 1760 pages used for memmap
>  Normal zone: 223520 pages, LIFO batch:31
>  HighMem zone: 2301 pages used for memmap
>  HighMem zone: 292339 pages, LIFO batch:31
>DMI present.
>Using APIC driver default
>ACPI: RSDP 000F6BA0, 0014 (r0 PTLTD )
>ACPI: RSDT 7FEFA0CA, 0030 (r1 PTLTD    RSDT    6040000  LTP        0)
>ACPI: FACP 7FEFEEF0, 0074 (r1 HP     WOMBAT    6040000 PTL         8)
>ACPI: DSDT 7FEFA0FA, 4DF6 (r1     HP   Wombat  6040000 MSFT  100000B)
>ACPI: FACS 7FEFFFC0, 0040
>ACPI: APIC 7FEFEF64, 0074 (r1 PTLTD  	 APIC    6040000  LTP        0)
>ACPI: BOOT 7FEFEFD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
>ACPI: PM-Timer IO Port: 0x1008
>ACPI: Local APIC address 0xfee00000
>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>Processor #0 15:0 APIC version 20
>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled)
>Processor #6 15:0 APIC version 20
>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
>ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
>IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
>ACPI: IOAPIC (id[0x02] address[0xfec80000] gsi_base[24])
>IOAPIC[1]: apic_id 2, version 32, address 0xfec80000, GSI 24-47
>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
>ACPI: IRQ0 used by override.
>ACPI: IRQ2 used by override.
>ACPI: IRQ9 used by override.
>Enabling APIC mode:  Flat.  Using 2 I/O APICs
>Using ACPI (MADT) for SMP configuration information
>Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
>Built 1 zonelists.  Total pages: 519923
>Kernel command line: root=/dev/disk/by-id/scsi-200e09e002bccccf9-part1 vga=0x31a    resume=/dev/sdb2 splash=silent
>bootsplash: silent mode.
>mapped APIC to ffffd000 (fee00000)
>mapped IOAPIC to ffffc000 (fec00000)
>mapped IOAPIC to ffffb000 (fec80000)
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Initializing CPU#0
>PID hash table entries: 4096 (order: 12, 16384 bytes)
>Detected 1695.948 MHz processor.
>Console: colour dummy device 80x25
>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
>Memory: 2069668k/2096064k available (1805k kernel code, 25136k reserved, 756k data, 208k init, 1178560k highmem)
>virtual kernel memory layout:
>    fixmap  : 0xffdf5000 - 0xfffff000   (2088 kB)
>    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
>    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
>    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
>      .init : 0xc0388000 - 0xc03bc000   ( 208 kB)
>      .data : 0xc02c37d1 - 0xc0380924   ( 756 kB)
>      .text : 0xc0100000 - 0xc02c37d1   (1805 kB)
>Checking if this processor honours the WP bit even in supervisor mode... Ok.
>Calibrating delay using timer specific routine.. 3395.43 BogoMIPS (lpj=6790860)
>Security Framework v1.0.0 initialized
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 256K
>CPU: Hyper-Threading is disabled
>CPU: After all inits, caps: 3febfbff 00000000 00000000 0000b080 00000000 00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU0: Thermal monitoring enabled
>Compat vDSO mapped to ffffe000.
>Checking 'hlt' instruction... OK.
>SMP alternatives: switching to UP code
>Unpacking initramfs... done
>Freeing initrd memory: 4532k freed
>ACPI: Core revision 20070126
>Parsing all Control Methods:
>Table [DSDT](id 0001) - 423 Objects with 37 Devices 136 Methods 19 Regions
> tbxface-0587 [00] tb_load_namespace     : ACPI Tables successfully acquired
>evxfevnt-0091 [00] enable                : Transition to ACPI mode successful
>CPU0: Intel(R) Xeon(TM) CPU 1700MHz stepping 0a
>SMP alternatives: switching to SMP code
>Booting processor 1/6 eip 3000
>Initializing CPU#1
>Calibrating delay using timer specific routine.. 3392.00 BogoMIPS (lpj=6784012)
>CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
>CPU: Trace cache: 12K uops, L1 D cache: 8K
>CPU: L2 cache: 256K
>CPU: Hyper-Threading is disabled
>CPU: After all inits, caps: 3febfbff 00000000 00000000 0000b080 00000000 00000000 00000000
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#1.
>CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
>CPU1: Thermal monitoring enabled
>CPU1: Intel(R) Xeon(TM) CPU 1700MHz stepping 0a
>Total of 2 processors activated (6787.43 BogoMIPS).
>ENABLING IO-APIC IRQs
>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
>checking TSC synchronization [CPU#0 -> CPU#1]: passed.
>Brought up 2 CPUs
>migration_cost=303
>NET: Registered protocol family 16
>ACPI: bus type pci registered
>PCI: PCI BIOS revision 2.10 entry at 0xfd91b, last bus=4
>PCI: Using configuration type 1
>Setting up standard PCI resources
>evgpeblk-0952 [00] ev_create_gpe_block   : GPE 00 to 0F [_GPE] 2 regs on int 0x9
>evgpeblk-0952 [00] ev_create_gpe_block   : GPE 10 to 1F [_GPE] 2 regs on int 0x9
>evgpeblk-1048 [00] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 0 Runtime GPEs in this block
>evgpeblk-1048 [00] ev_initialize_gpe_bloc: Found 2 Wake, Enabled 0 Runtime GPEs in this block
>Completing Region/Field/Buffer/Package initialization:.......................................................................................
>Initialized 19/19 Regions 0/0 Fields 38/38 Buffers 30/36 Packages (432 nodes)
>Initializing Device/Processor/Thermal objects by executing _INI methods:
>Executed 0 _INI methods requiring 0 _STA executions (examined 41 objects)
>ACPI: Interpreter enabled
>ACPI: (supports S0 S1 S4 S5)
>ACPI: Using IOAPIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
>PCI quirk: region 1180-11bf claimed by ICH4 GPIO
>PCI: Firmware left 0000:04:0d.0 e100 interrupts enabled, disabling
>PCI: Transparent bridge - 0000:00:1e.0
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HLB_.P64H._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT]
>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 14 15)
>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 14 15)
>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 9 10 *11 14 15)
>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 9 10 11 14 15)
>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 14 15)
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI init
>ACPI: bus type pnp registered
>pnp: PnP ACPI: found 13 devices
>ACPI: ACPI bus type pnp unregistered
>PnPBIOS: Disabled by ACPI PNP
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
>Time: tsc clocksource has been installed.
>ACPI: RTC can wake from S4
>PCI: Failed to allocate mem resource #6:10000@f8000000 for 0000:01:00.0
>PCI: Bridge: 0000:00:01.0
>  IO window: disabled.
>  MEM window: e8000000-e8ffffff
>  PREFETCH window: f0000000-f7ffffff
>PCI: Bridge: 0000:02:1f.0
>  IO window: 2000-2fff
>  MEM window: e9000000-e90fffff
>  PREFETCH window: disabled.
>PCI: Bridge: 0000:00:02.0
>  IO window: 2000-2fff
>  MEM window: e9000000-e90fffff
>  PREFETCH window: disabled.
>PCI: Bridge: 0000:00:1e.0
>  IO window: 3000-3fff
>  MEM window: e9100000-e91fffff
>  PREFETCH window: 88000000-880fffff
>PCI: Setting latency timer of device 0000:02:1f.0 to 64
>PCI: Setting latency timer of device 0000:00:1e.0 to 64
>NET: Registered protocol family 2
>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
>TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
>TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>TCP reno registered
>Simple Boot Flag at 0x3e set to 0x1
>Machine check exception polling timer started.
>audit: initializing netlink socket (disabled)
>audit(1188817835.684:1): initialized
>highmem bounce pool size: 64 pages
>Total HugeTLB memory allocated, 0
>VFS: Disk quotas dquot_6.5.1
>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered (default)
>Boot video device is 0000:01:00.0
>vesafb: framebuffer at 0xf0000000, mapped to 0xf8880000, using 10240k, total 32768k
>vesafb: mode is 1280x1024x16, linelength=2560, pages=1
>vesafb: protected mode interface info at c000:0f3e
>vesafb: pmi: set display start = c00c0f77, set palette = c00c0fed
>vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
>vesafb: scrolling: redraw
>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 98233 bytes,<6>...found (1280x1024, 35219 bytes, v3).
>Console: switching to colour frame buffer device 156x60
>Switched to NOHz mode on CPU #1
>Switched to NOHz mode on CPU #0
>fb0: VESA VGA frame buffer device
>isapnp: Scanning for PnP cards...
>isapnp: No Plug & Play device found
>Real Time Clock Driver v1.12ac
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>Floppy drive(s): fd0 is 1.44M
>FDC 0 is a National Semiconductor PC87306
>PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MOUS] at 0x60,0x64 irq 1,12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>mice: PS/2 mouse device common for all mice
>input: AT Translated Set 2 keyboard as /class/input/input0
>input: PC Speaker as /class/input/input1
>NET: Registered protocol family 1
>Using IPI No-Shortcut mode
>Freeing unused kernel memory: 208k freed
>SCSI subsystem initialized
>libata version 3.00 loaded.
>ata_piix 0000:00:1f.1: version 2.11
>PCI: Setting latency timer of device 0000:00:1f.1 to 64
>scsi0 : ata_piix
>scsi1 : ata_piix
>ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011090 irq 14
>ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011098 irq 15
>ata1.00: ATA-4: QUANTUM FIREBALL CR6.4A, A5U.1400, max UDMA/66
>ata1.00: 12594960 sectors, multi 16: LBA 
>ata1.00: limited to UDMA/33 due to 40-wire cable
>ata1.00: configured for UDMA/33
>ata2.00: ATAPI: Hewlett-Packard CD-Writer Plus 9500b, 1.06, max MWDMA2
>ata2.00: configured for MWDMA2
>scsi 0:0:0:0: Direct-Access     ATA      QUANTUM FIREBALL A5U. PQ: 0 ANSI: 5
>scsi 1:0:0:0: CD-ROM            HP       CD-Writer+ 9500b 1.06 PQ: 0 ANSI: 5
>ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 23 (level, low) -> IRQ 16
>sym0: <1010-66> rev 0x1 at pci 0000:03:08.0 irq 16
>sym0: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
>sym0: open drain IRQ line driver, using on-chip SRAM
>sym0: using LOAD/STORE-based firmware.
>sym0: handling phase mismatch from SCRIPTS.
>sym0: SCSI BUS has been reset.
>scsi2 : sym-2.2.3
>scsi 2:0:0:0: Direct-Access     QUANTUM  ATLAS10K2-TY184L DA40 PQ: 0 ANSI: 3
> target2:0:0: tagged command queuing enabled, command queue depth 16.
> target2:0:0: Beginning Domain Validation
> target2:0:0: asynchronous
> target2:0:0: wide asynchronous
> target2:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 31)
> target2:0:0: Domain Validation skipping write tests
> target2:0:0: Ending Domain Validation
>ACPI: PCI Interrupt 0000:03:08.1[B] -> GSI 19 (level, low) -> IRQ 17
>sym1: <1010-66> rev 0x1 at pci 0000:03:08.1 irq 17
>sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
>sym1: open drain IRQ line driver, using on-chip SRAM
>sym1: using LOAD/STORE-based firmware.
>sym1: handling phase mismatch from SCRIPTS.
>sym1: SCSI BUS has been reset.
>scsi3 : sym-2.2.3
>scsi 3:0:6:0: Direct-Access     WDIGTL   WDE9180 ULTRA2   1.30 PQ: 0 ANSI: 2
> target3:0:6: tagged command queuing enabled, command queue depth 16.
> target3:0:6: Beginning Domain Validation
> target3:0:6: asynchronous
>scsi 3:0:6:0: ODD transfer in DATA IN phase.
>scsi 3:0:6:0: COMMAND FAILED (87 0 10).
> target3:0:6: Wide Transfers Fail
> target3:0:6: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 31)
> target3:0:6: Domain Validation skipping write tests
> target3:0:6: Ending Domain Validation
>scsi scan: INQUIRY result too short (5), using 36
>BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
>usbcore: registered new interface driver usbfs
>usbcore: registered new interface driver hub
>usbcore: registered new device driver usb
>USB Universal Host Controller Interface driver v3.0
>PCI: Enabling device 0000:00:1f.2 (0004 -> 0005)
>ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 17
>PCI: Setting latency timer of device 0000:00:1f.2 to 64
>uhci_hcd 0000:00:1f.2: UHCI Host Controller
>uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
>uhci_hcd 0000:00:1f.2: irq 17, io base 0x000010a0
>sd 0:0:0:0: [sda] 12594960 512-byte hardware sectors (6449 MB)
>sd 0:0:0:0: [sda] Write Protect is off
>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>sd 0:0:0:0: [sda] 12594960 512-byte hardware sectors (6449 MB)
>sd 0:0:0:0: [sda] Write Protect is off
>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sda: sda1
>usb usb1: new device found, idVendor=0000, idProduct=0000
>sd 0:0:0:0: [sda] Attached SCSI disk
>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
>usb usb1: Product: UHCI Host Controller
>sd 2:0:0:0: [sdb] 35566480 512-byte hardware sectors (18210 MB)
>usb usb1: Manufacturer: Linux 2.6.22.3-7-default uhci_hcd
>sd 2:0:0:0: [sdb] Write Protect is off
>sd 2:0:0:0: [sdb] Mode Sense: f5 00 10 08
>usb usb1: SerialNumber: 0000:00:1f.2
>usb usb1: configuration #1 chosen from 1 choice
>sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
>hub 1-0:1.0: USB hub found
>sd 2:0:0:0: [sdb] 35566480 512-byte hardware sectors (18210 MB)
>hub 1-0:1.0: 2 ports detected
>sd 2:0:0:0: [sdb] Write Protect is off
>sd 2:0:0:0: [sdb] Mode Sense: f5 00 10 08
>sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
> sdb: sdb1 sdb2
>sd 2:0:0:0: [sdb] Attached SCSI disk
>sd 3:0:6:0: [sdc] 17873040 512-byte hardware sectors (9151 MB)
>sd 3:0:6:0: [sdc] Write Protect is off
>sd 3:0:6:0: [sdc] Mode Sense: a7 00 00 08
>sd 3:0:6:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>usb 1-2: new low speed USB device using uhci_hcd and address 2
>sd 3:0:6:0: [sdc] 17873040 512-byte hardware sectors (9151 MB)
>sd 3:0:6:0: [sdc] Write Protect is off
>sd 3:0:6:0: [sdc] Mode Sense: a7 00 00 08
>sd 3:0:6:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sdc: sdc1
>sd 3:0:6:0: [sdc] Attached SCSI disk
>usb 1-2: new device found, idVendor=046d, idProduct=c016
>usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
>usb 1-2: Product: Optical USB Mouse
>usb 1-2: Manufacturer: Logitech
>usb 1-2: configuration #1 chosen from 1 choice
>usbcore: registered new interface driver hiddev
>input: Logitech Optical USB Mouse as /class/input/input2
>input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1f.2-2
>usbcore: registered new interface driver usbhid
>drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
>swsusp: Basic memory bitmaps created
>swsusp: Basic memory bitmaps freed
>Attempting manual resume
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sdb1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>sd 0:0:0:0: Attached scsi generic sg0 type 0
>scsi 1:0:0:0: Attached scsi generic sg1 type 5
>sd 2:0:0:0: Attached scsi generic sg2 type 0
>sd 3:0:6:0: Attached scsi generic sg3 type 0
>Linux agpgart interface v0.102 (c) Dave Jones
>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>agpgart: Detected an Intel i860 Chipset.
>agpgart: AGP aperture is 64M @ 0xec000000
>ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 18
>shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
>rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
>rtc_cmos: probe of 00:04 failed with error -16
>iTCO_vendor_support: vendor-support=0
>EDAC MC: Ver: 2.0.1 Aug 20 2007
>parport_pc 00:0a: reported by Plug and Play ACPI
>parport0: PC-style at 0x278 (0x678), irq 5, dma 1 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
>input: Power Button (FF) as /class/input/input3
>ACPI: Power Button (FF) [PWRF]
>input: Power Button (CM) as /class/input/input4
>ACPI: Power Button (CM) [PWRB]
>EDAC i82860: i82860 init one
>EDAC MC0: Giving out device to i82860_edac i82860: DEV 0000:00:00.0
>sr0: scsi3-mmc drive: 31x/32x writer cd/rw xa/form2 cdda tray
>Uniform CD-ROM driver Revision: 3.20
>sr 1:0:0:0: Attached scsi CD-ROM sr0
>iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
>iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
>iTCO_wdt: No card detected
>intel_rng: FWH not detected
>ACPI: PCI Interrupt 0000:04:09.0[A] -> GSI 19 (level, low) -> IRQ 17
>3c59x: Donald Becker and others.
>0000:04:09.0: 3Com PCI 3c905C Tornado at f96a8000.
>8139too Fast Ethernet driver 0.9.28
>e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
>e100: Copyright(c) 1999-2006 Intel Corporation
>PCI: Enabling device 0000:00:1f.5 (0004 -> 0005)
>ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 18
>PCI: Setting latency timer of device 0000:00:1f.5 to 64
>intel8x0_measure_ac97_clock: measured 53399 usecs
>intel8x0: clocking to 48000
>ACPI: PCI Interrupt 0000:04:0d.0[A] -> GSI 21 (level, low) -> IRQ 19
>e100: eth1: e100_probe: addr 0xe9120000, irq 19, MAC addr 00:E0:81:00:1D:1B
>PCI: Enabling device 0000:04:0a.0 (0104 -> 0107)
>ACPI: PCI Interrupt 0000:04:0a.0[A] -> GSI 17 (level, low) -> IRQ 18
>eth2: RealTek RTL8139 at 0xf95fc400, 00:50:fc:a8:67:23, IRQ 18
>eth2:  Identified 8139 chip type 'RTL-8100B/8139D'
>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
>Adding 3092504k swap on /dev/sdb2.  Priority:-1 extents:1 across:3092504k
>device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
>loop: module loaded
>REISERFS (device sdc1): found reiserfs format "3.6" with standard journal
>REISERFS (device sdc1): using ordered data mode
>reiserfs: using flush barriers
>REISERFS (device sdc1): journal params: device sdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
>REISERFS (device sdc1): checking transaction log (sdc1)
>REISERFS (device sdc1): Using r5 hash to sort names
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on sda1, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>AppArmor: AppArmor initialized
>audit(1188817867.185:2):  info="AppArmor initialized" pid=1989
>bootsplash: status on console 0 changed to on
>powernow: This module only works with AMD K7 CPUs
>eth2: link down
>NET: Registered protocol family 10
>lo: Disabled Privacy Extensions
>ADDRCONF(NETDEV_UP): eth2: link is not ready
>Mobile IPv6
>ip6_tables: (C) 2000-2006 Netfilter Core Team
>ip_tables: (C) 2000-2006 Netfilter Core Team
>eth0:  setting half-duplex.
>ADDRCONF(NETDEV_UP): eth0: link is not ready
>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>st: Version 20070203, fixed bufsize 32768, s/g segs 256
>NET: Registered protocol family 17
>Netfilter messages via NETLINK v0.30.
>nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
>ISO 9660 Extensions: Microsoft Joliet Level 3
>ISO 9660 Extensions: RRIP_1991A
>ISO 9660 Extensions: Microsoft Joliet Level 3
>ISO 9660 Extensions: RRIP_1991A
>pnp: Device 00:0a disabled.
>parport 0x278 (WARNING): CTR: wrote 0x0c, read 0xff
>parport 0x278 (WARNING): DATA: wrote 0xaa, read 0xff
>parport 0x278: You gave this address, but there is probably no parallel port there!
>parport0: PC-style at 0x278 [PCSPP,TRISTATE]
>pnp: Device 00:0a activated.
>parport_pc 00:0a: reported by Plug and Play ACPI
>parport0: PC-style at 0x278 (0x678), irq 5, dma 1 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
>lp0: using parport0 (interrupt-driven).
>ACPI: PCI interrupt for device 0000:00:1f.5 disabled
>ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 18
>PCI: Setting latency timer of device 0000:00:1f.5 to 64
>intel8x0_measure_ac97_clock: measured 52395 usecs
>intel8x0: clocking to 48000
>end_request: I/O error, dev fd0, sector 0
>end_request: I/O error, dev fd0, sector 0
>IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
>eth2: link down
>ADDRCONF(NETDEV_UP): eth2: link is not ready
>ISO 9660 Extensions: Microsoft Joliet Level 3
>ISO 9660 Extensions: RRIP_1991A
>eth0:  setting half-duplex.
>ADDRCONF(NETDEV_UP): eth0: link is not ready
>usb 1-1: new full speed USB device using uhci_hcd and address 3
>usb 1-1: new device found, idVendor=0781, idProduct=5151
>usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3
>usb 1-1: Product: Cruzer Micro
>usb 1-1: Manufacturer: SanDisk Corporation
>usb 1-1: SerialNumber: 20060266021B45A29D2D
>usb 1-1: configuration #1 chosen from 1 choice
>Initializing USB Mass Storage driver...
>scsi4 : SCSI emulation for USB Mass Storage devices
>usb-storage: device found at 3
>usb-storage: waiting for device to settle before scanning
>usbcore: registered new interface driver usb-storage
>USB Mass Storage support registered.
>scsi 4:0:0:0: Direct-Access     SanDisk  Cruzer Micro     0.1  PQ: 0 ANSI: 2
>sd 4:0:0:0: [sdd] 4001760 512-byte hardware sectors (2049 MB)
>sd 4:0:0:0: [sdd] Write Protect is off
>sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00
>sd 4:0:0:0: [sdd] Assuming drive cache: write through
>sd 4:0:0:0: [sdd] 4001760 512-byte hardware sectors (2049 MB)
>sd 4:0:0:0: [sdd] Write Protect is off
>sd 4:0:0:0: [sdd] Mode Sense: 03 00 00 00
>sd 4:0:0:0: [sdd] Assuming drive cache: write through
> sdd: sdd1
>sd 4:0:0:0: [sdd] Attached SCSI removable disk
>sd 4:0:0:0: Attached scsi generic sg4 type 0
>usb-storage: device scan complete

Actions: View

Attachments on bug 307162: 161490 | 161491 | 161494 | 161495 | 161496 | 161497 | 162229