Attachment 57726 Details for Bug 132005

New dmesg output after making kernel

dmesg (text/plain), 23.84 KB, created by Kai Springer on 2005-11-18 14:26:20 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Kai Springer

Created: 2005-11-18 14:26:20 UTC

Size: 23.84 KB

patch

obsolete

>linux:/usr/src/kernel-modules/acx100-0.2.0pre8_plus_fixes_57/scripts # dmesg
>Linux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
>BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000001bff0000 (usable)
> BIOS-e820: 000000001bff0000 - 000000001bffffc0 (ACPI data)
> BIOS-e820: 000000001bffffc0 - 000000001c000000 (ACPI NVS)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
>0MB HIGHMEM available.
>447MB LOWMEM available.
>On node 0 totalpages: 114672
>  DMA zone: 4096 pages, LIFO batch:1
>  Normal zone: 110576 pages, LIFO batch:31
>  HighMem zone: 0 pages, LIFO batch:1
>DMI 2.3 present.
>ACPI: RSDP (v000 OID_00                                ) @ 0x000e5010
>ACPI: RSDT (v001 INSYDE RSDT_000 0x00000001 _CSI 0x00010101) @ 0x1bffc2e0
>ACPI: FADT (v001 INSYDE FACP_000 0x00000100 _CSI 0x00010101) @ 0x1bfffaa0
>ACPI: BOOT (v001 INSYDE SYS_BOOT 0x00000100 _CSI 0x00010101) @ 0x1bfffb90
>ACPI: DBGP (v001 INSYDE DBGP_000 0x00000100 _CSI 0x00010101) @ 0x1bfffbc0
>ACPI: MADT (v001 INSYDE APIC_000 0x30303030 0000 0x30303030) @ 0x1bfffb30
>ACPI: DSDT (v001 INSYDE   K8N800 0x00001000 INTL 0x02002036) @ 0x00000000
>ACPI: PM-Timer IO Port: 0x1008
>ACPI: local apic disabled
>Allocating PCI resources starting at 1c000000 (gap: 1c000000:e3f80000)
>Built 1 zonelists
>Kernel command line: root=/dev/hda3 vga=0x317 selinux=0    resume=/dev/hda2  splash=silent
>bootsplash: silent mode.
>Initializing CPU#0
>PID hash table entries: 2048 (order: 11, 32768 bytes)
>Detected 1604.017 MHz processor.
>Using pmtmr for high-res timesource
>Console: colour dummy device 80x25
>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
>Memory: 448976k/458688k available (2028k kernel code, 9096k reserved, 700k data, 204k init, 0k highmem)
>Checking if this processor honours the WP bit even in supervisor mode... Ok.
>Calibrating delay using timer specific routine.. 3210.67 BogoMIPS (lpj=6421355)
>Security Framework v1.0.0 initialized
>SELinux:  Disabled at boot.
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000000 00000000 00000001
>CPU: After vendor identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000000 00000000 00000001
>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>CPU: L2 Cache: 256K (64 bytes/line)
>CPU: After all inits, caps: 078bfbff c3d3fbff 00000000 00000010 00000000 00000000 00000001
>Intel machine check architecture supported.
>Intel machine check reporting enabled on CPU#0.
>mtrr: v2.0 (20020519)
>CPU: AMD Mobile AMD Sempron(tm) Processor 2800+ stepping 00
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Checking 'hlt' instruction... OK.
>checking if image is initramfs... it is
>Freeing initrd memory: 1722k freed
>ACPI: Looking for DSDT in initrd... not found!
> not found!
>ACPI: setting ELCR to 0200 (from 0ea0)
>NET: Registered protocol family 16
>ACPI: bus type pci registered
>PCI: PCI BIOS revision 2.10 entry at 0xe8944, last bus=1
>PCI: Using configuration type 1
>ACPI: Subsystem revision 20050408
>ACPI: Interpreter enabled
>ACPI: Using PIC for interrupt routing
>ACPI: PCI Root Bridge [PCI0] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
>ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
>Boot video device is 0000:01:00.0
>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>ACPI: Embedded Controller [EC0] (gpe 1)
>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *7 10 11 14 15)
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI init
>pnp: PnP ACPI: found 8 devices
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
>TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
>pnp: 00:05: ioport range 0x3f0-0x3f5 has been reserved
>pnp: 00:05: ioport range 0x680-0x68f has been reserved
>pnp: 00:05: ioport range 0x1000-0x107f could not be reserved
>PCI: Bridge: 0000:00:01.0
>  IO window: c000-dfff
>  MEM window: e0000000-efffffff
>  PREFETCH window: a0000000-afffffff
>PCI: Bus 2, cardbus bridge: 0000:00:09.0
>  IO window: 00002000-00002fff
>  IO window: 00003000-00003fff
>  PREFETCH window: 1c000000-1dffffff
>  MEM window: 1e000000-1fffffff
>    ACPI-0212: *** Warning: Device is not power manageable
>PCI: Setting latency timer of device 0000:00:01.0 to 64
>ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
>PCI: setting IRQ 10 as level-triggered
>ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
>Simple Boot Flag at 0x37 set to 0x1
>apm: BIOS not found.
>audit: initializing netlink socket (disabled)
>audit(1132321623.944:1): initialized
>Total HugeTLB memory allocated, 0
>VFS: Disk quotas dquot_6.5.1
>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>Initializing Cryptographic API
>vesafb: framebuffer at 0xa4000000, mapped to 0xdc880000, using 6144k, total 65536k
>vesafb: mode is 1024x768x16, linelength=2048, pages=41
>vesafb: protected mode interface info at c000:a1e6
>vesafb: scrolling: redraw
>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 76011 bytes,<6>...found (1024x768, 12703 bytes, v3).
>Console: switching to colour frame buffer device 127x44
>fb0: VESA VGA frame buffer device
>isapnp: Scanning for PnP cards...
>isapnp: No Plug & Play device found
>Real Time Clock Driver v1.12
>PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
>i8042.c: Detected active multiplexing controller, rev 1.1.
>serio: i8042 AUX0 port at 0x60,0x64 irq 12
>serio: i8042 AUX1 port at 0x60,0x64 irq 12
>serio: i8042 AUX2 port at 0x60,0x64 irq 12
>serio: i8042 AUX3 port at 0x60,0x64 irq 12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered
>floppy0: no floppy controllers found
>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
>loop: loaded (max 8 devices)
>mice: PS/2 mouse device common for all mice
>input: PC Speaker
>md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
>md: bitmap version 3.38
>NET: Registered protocol family 2
>input: AT Translated Set 2 keyboard on isa0060/serio0
>IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
>TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
>TCP: Hash tables configured (established 16384 bind 16384)
>TCP reno registered
>NET: Registered protocol family 1
>Using IPI Shortcut mode
>ACPI wakeup devices:
>SBTN USB0 USB1 USB2 EHCI AC97 MC97 LAN0
>ACPI: (supports S0 S3 S4 S5)
>Freeing unused kernel memory: 204k freed
>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>VP_IDE: IDE controller at PCI slot 0000:00:11.1
>    ACPI-0212: *** Warning: Device is not power manageable
>ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
>PCI: setting IRQ 11 as level-triggered
>ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
>PCI: Via IRQ fixup for 0000:00:11.1, from 0 to 11
>VP_IDE: chipset revision 6
>VP_IDE: not 100% native mode: will probe irqs later
>VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
>    ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:pio
>    ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc:DMA, hdd:pio
>Probing IDE interface ide0...
>hda: FUJITSU MHT2040AT, ATA DISK drive
>Synaptics Touchpad, model: 1, fw: 5.9, id: 0x256eb1, caps: 0x804713/0x0
>input: SynPS/2 Synaptics TouchPad on isa0060/serio3
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>hda: max request size: 128KiB
>hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
>hda: cache flushes supported
> hda: hda1 hda2 hda3
>Probing IDE interface ide1...
>hdc: MATSHITAUJ-840D, ATAPI CD/DVD-ROM drive
>ide1 at 0x170-0x177,0x376 on irq 15
>ACPI: CPU0 (power states: C1[C1] C2[C2])
>ACPI: Thermal Zone [TZ0] (52 C)
>hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
>Uniform CD-ROM driver Revision: 3.20
>Attempting manual resume
>swsusp: Suspend partition has wrong signature?
>ReiserFS: hda3: found reiserfs format "3.6" with standard journal
>ReiserFS: hda3: using ordered data mode
>ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
>ReiserFS: hda3: checking transaction log (hda3)
>ReiserFS: hda3: Using r5 hash to sort names
>bootsplash: status on console 0 changed to on
>md: Autodetecting RAID arrays.
>md: autorun ...
>md: ... autorun DONE.
>Adding 907664k swap on /dev/hda2.  Priority:-1 extents:1
>device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
>lp: driver loaded but no devices found
>NET: Registered protocol family 10
>Disabled Privacy Extensions on device c036b920(lo)
>IPv6 over IPv4 tunneling driver
>ip6_tables: (C) 2000-2002 Netfilter core team
>Linux agpgart interface v0.101 (c) Dave Jones
>agpgart: Detected AGP bridge 0
>agpgart: AGP aperture is 256M @ 0xb0000000
>usbcore: registered new driver usbfs
>usbcore: registered new driver hub
>USB Universal Host Controller Interface driver v2.3
>    ACPI-0212: *** Warning: Device is not power manageable
>ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
>uhci_hcd 0000:00:10.0: UHCI Host Controller
>uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
>uhci_hcd 0000:00:10.0: irq 11, io base 0x00001200
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 2 ports detected
>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
>shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
>    ACPI-0212: *** Warning: Device is not power manageable
>ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
>uhci_hcd 0000:00:10.1: UHCI Host Controller
>uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
>uhci_hcd 0000:00:10.1: irq 10, io base 0x00001300
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
>Yenta: CardBus bridge found at 0000:00:09.0 [1071:8889]
>Yenta: Using CSCINT to route CSC interrupts to PCI
>Yenta: Routing CardBus interrupts to PCI
>Yenta TI: socket 0000:00:09.0, mfunc 0x01021c02, devctl 0x44
>ip_tables: (C) 2000-2002 Netfilter core team
>    ACPI-0212: *** Warning: Device is not power manageable
>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
>PCI: setting IRQ 5 as level-triggered
>ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
>uhci_hcd 0000:00:10.2: UHCI Host Controller
>uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
>uhci_hcd 0000:00:10.2: irq 5, io base 0x00001700
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 2 ports detected
>via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
>ip_conntrack version 2.1 (3583 buckets, 28664 max) - 248 bytes per conntrack
>Yenta: ISA IRQ mask 0x0050, PCI irq 10
>Socket status: 30000020
>    ACPI-0212: *** Warning: Device is not power manageable
>ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
>PCI: setting IRQ 7 as level-triggered
>ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 7 (level, low) -> IRQ 7
>ehci_hcd 0000:00:10.3: EHCI Host Controller
>ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
>ehci_hcd 0000:00:10.3: irq 7, io mem 0xf0000000
>ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 6 ports detected
>    ACPI-0212: *** Warning: Device is not power manageable
>ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
>eth0: VIA Rhine II at 0x1e200, 00:40:d0:6d:68:c0, IRQ 11.
>eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
>via82xx: Assuming DXS channels with 48k fixed sample rate.
>         Please try dxs_support=5 option
>         and report if it works on your machine.
>         For more details, read ALSA-Configuration.txt.
>ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
>PCI: Setting latency timer of device 0000:00:11.5 to 64
>NET: Registered protocol family 23
>via_ircc: module not supported by Novell, setting U taint flag.
>    ACPI-0212: *** Warning: Device is not power manageable
>acx_pci: module not supported by Novell, setting U taint flag.
>PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
>ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
>PCI: Setting latency timer of device 0000:02:00.0 to 64
>cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
>cs: IO port probe 0x100-0x3af: clean.
>cs: IO port probe 0xc00-0xcff: clean.
>cs: IO port probe 0x820-0x8ff: clean.
>cs: IO port probe 0xa00-0xaff: clean.
>bootsplash: status on console 0 changed to on
>BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
>eth0: link down
>NET: Registered protocol family 17
>ACPI: PCI interrupt for device 0000:02:00.0 disabled
>acx_pci: probe of 0000:02:00.0 failed with error -5
>eth0: no IPv6 routers present
>ACPI: AC Adapter [AC] (on-line)
>ACPI: Battery Slot [BAT0] (battery present)
>ACPI: Power Button (FF) [PWRF]
>ACPI: Lid Switch [LID]
>ACPI: Sleep Button (CM) [SBTN]
>IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
>microcode: CPU0 not a capable Intel processor
>microcode: No new microcode data for CPU0
>IA-32 Microcode Update Driver v1.14 unregistered
>bootsplash: status on console 0 changed to on
>powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.3)
>powernow-k8:    0 : fid 0x8 (1600 MHz), vid 0x8 (1350 mV)
>powernow-k8:    1 : fid 0x0 (800 MHz), vid 0x13 (1075 mV)
>cpu_init done, current fid 0x8, vid 0x8
>bootsplash: status on console 0 changed to on
>subfs 0.9
>ISO 9660 Extensions: Microsoft Joliet Level 3
>ISO 9660 Extensions: RRIP_1991A
>ISO 9660 Extensions: Microsoft Joliet Level 3
>ISO 9660 Extensions: RRIP_1991A
>ISO 9660 Extensions: Microsoft Joliet Level 3
>ISO 9660 Extensions: RRIP_1991A
>PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
>ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
>PCI: Setting latency timer of device 0000:02:00.0 to 64
>ACPI: PCI interrupt for device 0000:02:00.0 disabled
>acx_pci: probe of 0000:02:00.0 failed with error -5
>PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
>ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
>PCI: Setting latency timer of device 0000:02:00.0 to 64
>ACPI: PCI interrupt for device 0000:02:00.0 disabled
>acx_pci: probe of 0000:02:00.0 failed with error -5
>acx_pci: no version for "struct_module" found: kernel tainted.
>acx_pci: module not supported by Novell, setting U taint flag.
>acx100: It looks like you've been coaxed into buying a wireless network card
>acx100: that uses the mysterious ACX100/ACX111 chip from Texas Instruments.
>acx100: You should better have bought e.g. a PRISM(R) chipset based card,
>acx100: since that would mean REAL vendor Linux support.
>acx100: Given this info, it's evident that this driver is still EXPERIMENTAL,
>acx100: thus your mileage may vary. Reading README file and/or Craig's HOWTO is
>recommended, visit http://acx100.sf.net in case of further questions/discussion.
>acx100: Compiled to use 32bit I/O access (faster, however I/O timing issues might occur, such as non-working firmware upload!) instead of 16bit access
>Running on a little-endian CPU
>acx_init_module: TI acx_pci.o: Ver 0.2.0pre8 driver initialized, waiting for cards to probe...
>ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
>acx_probe_pci: WARNING: ACX111 support is quite experimental!
>Found ACX111-based wireless network card at 0000:02:00.0, irq:10, phymem1:0x1e020000, phymem2:0x1e000000, mem1:0xdced8000, mem1_size:8192, mem2:0xdcf40000, mem2_size:131072
>initial debug setting is 0x000b
>acx_select_io_register_set: using ACX111 io resource addresses (size: 56)
>hw_unavailable = 1
>acx_probe_pci: TI acx_pci: Using IRQ 10
>reset hw_unavailable++
>acx_reset_mac: enable soft reset...
>acx_reset_mac: disable soft reset and go to init mode...
>Requesting firmware image 'TIACX111.BIN'
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #1 FAILED, retrying...
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #2 FAILED, retrying...
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #3 FAILED, retrying...
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #4 FAILED, retrying...
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #5 FAILED, retrying...
>acx_reset_dev: Failed to upload firmware to the ACX1xx
>acx_probe_pci: TI acx_pci: MAC initialize failure!
>ACPI: PCI interrupt for device 0000:02:00.0 disabled
>acx_probe_pci: TI acx_pci.o: Ver 0.2.0pre8 loading FAILED
>acx_pci: probe of 0000:02:00.0 failed with error -5
>eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=1 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=73 TOS=0x00 PREC=0x00 TTL=255 ID=2 DF PROTO=UDP SPT=5353 DPT=5353 LEN=53
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=3 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=4 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=5 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=6 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=7 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=8 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>acx_pci: module not supported by Novell, setting U taint flag.
>acx100: It looks like you've been coaxed into buying a wireless network card
>acx100: that uses the mysterious ACX100/ACX111 chip from Texas Instruments.
>acx100: You should better have bought e.g. a PRISM(R) chipset based card,
>acx100: since that would mean REAL vendor Linux support.
>acx100: Given this info, it's evident that this driver is still EXPERIMENTAL,
>acx100: thus your mileage may vary. Reading README file and/or Craig's HOWTO is
>recommended, visit http://acx100.sf.net in case of further questions/discussion.
>acx100: Compiled to use 32bit I/O access (faster, however I/O timing issues might occur, such as non-working firmware upload!) instead of 16bit access
>Running on a little-endian CPU
>acx_init_module: TI acx_pci.o: Ver 0.2.0pre8 driver initialized, waiting for cards to probe...
>ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
>acx_probe_pci: WARNING: ACX111 support is quite experimental!
>Found ACX111-based wireless network card at 0000:02:00.0, irq:10, phymem1:0x1e020000, phymem2:0x1e000000, mem1:0xdcedc000, mem1_size:8192, mem2:0xdcf40000, mem2_size:131072
>initial debug setting is 0x000b
>acx_select_io_register_set: using ACX111 io resource addresses (size: 56)
>hw_unavailable = 1
>acx_probe_pci: TI acx_pci: Using IRQ 10
>reset hw_unavailable++
>acx_reset_mac: enable soft reset...
>acx_reset_mac: disable soft reset and go to init mode...
>Requesting firmware image 'TIACX111.BIN'
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #1 FAILED, retrying...
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #2 FAILED, retrying...
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #3 FAILED, retrying...
>SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=192.168.2.107 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=9 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #4 FAILED, retrying...
>not using auto increment for firmware loading
>acx_write_fw: firmware written
>FATAL: firmware upload: data parts at offset 4 don't match (0xea000633 vs. 0x10003018)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>acx_write_fw (firmware): 0, acx_validate_fw: 1
>firmware upload attempt #5 FAILED, retrying...
>acx_reset_dev: Failed to upload firmware to the ACX1xx
>acx_probe_pci: TI acx_pci: MAC initialize failure!
>ACPI: PCI interrupt for device 0000:02:00.0 disabled
>acx_probe_pci: TI acx_pci.o: Ver 0.2.0pre8 loading FAILED
>acx_pci: probe of 0000:02:00.0 failed with error -5
>
>
>_______________________________________
>
>When I do a fetch_firmware and copy the newly received TIACX111.BIN to lib/firmware I get the following change in the dmesg outpout:
>
>
>ATAL: firmware upload: data parts at offset 4 don't match (0xea000435 vs. 0x99999999)! I/O timing issues or defective memory, with DWL-xx0+? Makefile: ACX_IO_WIDTH=16 should help. Please report!
>
>
>

Actions: View

Attachments on bug 132005: 56753 | 57726