Bug 148615

Please give more information about the hardware: `hwinfo --network'
What did you configure during the installation and what was wrong exactly afterwards? Please be more verbosive about this point.

OK 'hwinfo --network" is coming as attachment.

An entire "hwinfo" is in the case of Bug #141181

I du a NORMAL installation from 10.1 Beta3 with SLP from CD's only the boot Parameter apic is added.I had always after first reboot a not functioning network.

With older versions there are no problems (SL9.3, SL10, SLES9)

I found the error by coincidence.

With me there are problems with the network with the SL10.1 Beta1-2.I must mostly draw, then again attach the network plug after booting the System.

I confounded the network cards, a ping to my "server" ran and i had at one time a network connection. I changed it again no network connection.

I hope that was detailed enough.

Sorry but this does not really help.
What did you configure: this means:
 Which of the both cards was configured as eth0, which one as eth1, and so on
What goes wrong:
 Are the devices swapped (eth0 should be eth1), do they not work at all, wrong IP adress, whatsoever. Please attach the output if `ifconfig' here.

It is a normal installation with DHCP and SLP fdrom my server. With the first Reboot the wrong Network-Card is handed over. YaST2 don't remember the correct device? The Device are not swapped, it is no IP Address in in the ifconfig output.I hope my remember is correct ?

I have no original ifconfig output waived.

Created attachment 66863 [details]
The original Logs from YaST2

Created attachment 66864 [details]
The hwinfo --network log

a wild guess: does  rcnetwork restart  help?

No, afterwards the ifconfig output shows mostly only the lo device or nothing ?

I mean in the ifconfig output, at the fist time after reboot the deviices have only IPv6 addresses ?

> It is a normal installation with DHCP and SLP fdrom my server. With the first
> Reboot the wrong Network-Card is handed over.

> No, afterwards the ifconfig output shows mostly only the lo device or nothing ?

I still don't know the excat problem and these two comments are inconsistent.
Are you using NetworkManager?

I can't use Networkmanager ? I tell bevor:
.
I use a installation with the SUSE-10.1-CD-OSS-i386-Beta3-mini.iso, over DHCP and SLP. On my "Server" I have installad "YaST2 Installations Server" (works fine with "SLES9 7 CD's" and "SL10 DVD9" "SL9.3 5 CD's" ec.).The "SL10.1 5 CD's" works not.

I make a normal Install, after the 1. CD instalation, YaST2.make the FIST REBOOT, OK ?

Afterwards YaST2 continue with the installation with the  2. CD 
(on this Place the first Bug is shown Bug #141181)

I correct the Path frpm /data1/SL10.2 to /data/SL10.1 and say OK.

The next are the Network-Problem!

YaST2 change after the reboot the Device.

You say:
these two comments are inconsisten ??

Question: Comment #7
Answer: No, afterwards the ifconfig output shows mostly only the "lo" device or nothing ?

the answer:
I mean in the ifconfig output, at the fist time after reboot the deviices have
only IPv6 addresses ?

was a comment.
Additional:
in the ifconfig output are no IP v4 from the DHCP Server 


 

Please attach the /etc/sysconfig/network directory which contains your network configuration.

Created attachment 67020 [details]
Status after first reboot

This is the Status AFTER the first reboot

Created attachment 67024 [details]
Status: YaST2 Log after the first reboot

This are the YaST2 Logs after a clean new install after the first reboot.

Created attachment 67026 [details]
This is the running config

This is after config with YaST2 on a runnin installation from SL10.1

We'll check this. Setting to NEED in the meantime.

What is now?

NEED you INFO ??

Additional Info:

YaST2 always uses after reboot the not attached DEVICE ?

This is a duplicate.

*** This bug has been marked as a duplicate of 116537 ***