I´ve the above card installed in a PCMCIA socket.
YaST2 recogizes it as "Marvell 88w8335 [Libertas] 802.11b/g Wireless", but when
I click configure, firsst I get a message that there´s no module for that card.
ten its device type is "ethernet". If I change it to "wireless" and configure
the card, it will not work.
hwinfo --netcard returns:
21: PCI 208.0: 0200 Ethernet controller
  [Created at pci.277]
  UDI: /org/freedesktop/Hal/devices/pci_8086_1038
  Unique ID: rBUF.SPbcKWAadaA
  Parent ID: 6NW+.+nd8koiLHvC
  SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:08.0
  SysFS BusID: 0000:02:08.0
  Hardware Class: network
  Model: "Compaq 82801CAM (ICH3) PRO/100 VM (KM) Ethernet Controller"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x1038 "82801CAM (ICH3) PRO/100 VM (KM) Ethernet Controller"
  SubVendor: pci 0x0e11 "Compaq Computer Corporation"
  SubDevice: pci 0x0098
  Revision: 0x41
  Driver: "e100"
  Device File: eth0
  Memory Range: 0x40100000-0x40100fff (rw,non-prefetchable)
  I/O Ports: 0x2800-0x283f (rw)
  IRQ: 11 (1516 events)
  HW Address: 00:02:a5:b8:1b:0f
  Link detected: yes
  Module Alias: "pci:v00008086d00001038sv00000E11sd00000098bc02sc00i00"
  Driver Info #0:
    Driver Status: e100 is active
    Driver Activation Cmd: "modprobe e100"
  Driver Info #1:
    Driver Status: eepro100 is not active
    Driver Activation Cmd: "modprobe eepro100"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #14 (PCI bridge)

23: PCI 700.0: 0200 Ethernet controller
  [Created at pci.277]
  UDI: /org/freedesktop/Hal/devices/pci_11ab_1faa
  Unique ID: aK5u.ptqw5XL7l0A
  Parent ID: HjjP.d2w3vhM5MDF
  SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:03.1/0000:07:00.0
  SysFS BusID: 0000:07:00.0
  Hardware Class: network
  Model: "Marvell 88w8335 [Libertas] 802.11b/g Wireless"
  Hotplug: CardBus
  Socket: 1
  Vendor: pci 0x11ab "Marvell Technology Group Ltd."
  Device: pci 0x1faa "88w8335 [Libertas] 802.11b/g Wireless"
  SubVendor: pci 0x11ab "Marvell Technology Group Ltd."
  SubDevice: pci 0x1faa
  Revision: 0x03
  Memory Range: 0x18000000-0x1800ffff (rw,non-prefetchable,disabled)
  Memory Range: 0x18010000-0x1801ffff (rw,non-prefetchable,disabled)
  IRQ: 11 (1516 events)
  Module Alias: "pci:v000011ABd00001FAAsv000011ABsd00001FAAbc02sc00i00"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #19 (CardBus bridge)
Is it not possible to get this card working in SuSE or should I post a YaST2 log?