Bugzilla – Bug 1216523
opensuse Leap 15.6 not boot on NXP i.MX93
Last modified: 2024-06-25 17:59:11 UTC
U-Boot 2023.04-00024-g5759fda62b3 (Oct 17 2023 - 21:52:12 +0800) CPU: i.MX93(52) rev1.1 1700 MHz (running at 1692 MHz) CPU: Industrial temperature grade (-40C to 105C) at 44C Reset cause: POR (0x1) Model: NXP i.MX93 11X11 EVK board DRAM: 2 GiB TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C2 0x52] SNK.Power3.0 on CC2 PDO 0: type 0, 5000 mV, 3000 mA [E] PDO 1: type 0, 9000 mV, 3000 mA [] PDO 2: type 0, 15000 mV, 3000 mA [] PDO 3: type 0, 20000 mV, 2250 mA [] Requesting PDO 3: 20000 mV, 750 mA Source accept request PD source ready! tcpc_pd_receive_message: Polling ALERT register, TCPC_ALERT_RX_STATUS bit failed, ret = -62 TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C2 0x51] TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C2 0x50] Core: 226 devices, 36 uclasses, devicetree: separate MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment [*]-Video Link 0adv7535_mipi2hdmi hdmi@3d: Can't find cec device id=0x3c fail to probe panel device hdmi@3d fail to get display timings probe video device failed, ret -19 [0] lcd-controller@4ae30000, video [1] dsi@4ae10000, video_bridge [2] hdmi@3d, panel adv7535_mipi2hdmi hdmi@3d: Can't find cec device id=0x3c fail to probe panel device hdmi@3d fail to get display timings probe video device failed, ret -19 In: serial Out: serial Err: serial BuildInfo: - ELE firmware version 0.0.11-7d272678 switch to partitions #0, OK mmc0(part 0) is current device UID: 0x98acb0cc 0xcc4ed85c 0x2e7fdea0 0xe63cb5fd flash target is MMC:0 Net: eth0: ethernet@42890000, eth1: ethernet@428a0000 [PRIME] Fastboot: Normal Normal Boot Hit any key to stop autoboot: 0 u-boot=> gpio clear gpio@22_13 gpio: pin gpio@22_13 (gpio 13) value is 0 u-boot=> boot Working FDT set to 83000000 /usbg1 /usbg2 /wdt-reboot /rm67199_panel /dsi-host /display-subsystem /soc@0/bus@44000000/dma-controller@44000000 /soc@0/bus@44000000/sai@443b0000 /soc@0/bus@44000000/mqs1 /soc@0/bus@44000000/bbnsm@44440000 /soc@0/bus@44000000/system-controller@44460000 /soc@0/bus@44000000/tmu@44482000 /soc@0/bus@44000000/micfil@44520000 /soc@0/bus@42000000/dma-controller@42000000 /soc@0/bus@44000000/i3c-master@44330000 /soc@0/bus@42000000/i3c-master@42520000 /soc@0/bus@42/soc@0/bus@42000000/sai@42650000 libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND /soc@0/bus@42000000/sai@42660000 /soc@0/bus@42000000/mqs2 /soc@0/bus@42000000/xcvr@42680000 /soc@0/bus@42000000/flexio@425c0000 /soc@0/bus@42800000/epxp@4ae20000 Booting a command list Loading kernel ... Loading initial ramdisk ... EFI stub: Booting Linux Kernel... EFI stub: EFI_RNG_PROTOCOL unavailable EFI stub: Using DTB from configuration table EFI stub: Exiting boot services... [ 0.000000][ T0] Booting Linux on physical CPU 0x0000000000 [0x412fd050] [ 0.000000][ T0] Linux version 5.14.21-150500.55.28-default (geeko@buildhost) (gcc (SUSE Linux) 7.5.0, GNU ld (GNU Binut)[ 0.000000][ T0] Machine model: NXP i.MX93 11X11 EVK board [ 0.000000][ T0] efi: EFI v2.100 by Das U-Boot [ 0.000000][ T0] efi: ESRT=0xfbe9e040 RTPROP=0xfbea0040 SMBIOS=0xfbe9c000 MOKvar=0xfbdcc000 MEMRESERVE=0xfbae1040 [ 0.000000][ T0] esrt: Reserving ESRT space from 0x00000000fbe9e040 to 0x00000000fbe9e078. [ 0.000000][ T0] Reserved memory: created CMA memory pool at 0x00000000b0000000, size 256 MiB [ 0.000000][ T0] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000][ T0] earlycon: lpuart32 at MMIO32 0x0000000044380000 (options '') [ 0.000000][ T0] printk: bootconsole [lpuart32] enabled [ 0.000000][ T0] NUMA: No NUMA configuration found [ 0.000000][ T0] NUMA: Faking a node at [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000][ T0] NUMA: NODE_DATA [mem 0xffbe7280-0xffbebfff] [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000][ T0] DMA32 empty [ 0.000000][ T0] Normal empty [ 0.000000][ T0] Device empty [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000080000000-0x0000000095ffffff] [ 0.000000][ T0] node 0: [mem 0x0000000096000000-0x0000000097ffffff] [ 0.000000][ T0] node 0: [mem 0x0000000098000000-0x00000000fbdcbfff] [ 0.000000][ T0] node 0: [mem 0x00000000fbdcc000-0x00000000fbdccfff] [ 0.000000][ T0] node 0: [mem 0x00000000fbdcd000-0x00000000fbe9bfff] [ 0.000000][ T0] node 0: [mem 0x00000000fbe9c000-0x00000000fbe9cfff] [ 0.000000][ T0] node 0: [mem 0x00000000fbe9d000-0x00000000fbe9ffff] [ 0.000000][ T0] node 0: [mem 0x00000000fbea0000-0x00000000fbea0fff] [ 0.000000][ T0] node 0: [mem 0x00000000fbea1000-0x00000000fbea3fff] [ 0.000000][ T0] node 0: [mem 0x00000000fbea4000-0x00000000fbea5fff] [ 0.000000][ T0] node 0: [mem 0x00000000fbea6000-0x00000000fbea6fff] [ 0.000000][ T0] node 0: [mem 0x00000000fbea7000-0x00000000fbec8fff] [ 0.000000][ T0] node 0: [mem 0x00000000fbec9000-0x00000000feedffff] [ 0.000000][ T0] node 0: [mem 0x00000000feee0000-0x00000000feeeffff] [ 0.000000][ T0] node 0: [mem 0x00000000feef0000-0x00000000ffffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000][ T0] psci: probing for conduit method from DT. [ 0.000000][ T0] psci: PSCIv1.1 detected in firmware. [ 0.000000][ T0] psci: Using standard PSCI v0.2 function IDs [ 0.000000][ T0] psci: Trusted OS migration not required [ 0.000000][ T0] psci: SMC Calling Convention v1.2 [ 0.000000][ T0] percpu: Embedded 30 pages/cpu s84056 r8192 d30632 u122880 [ 0.000000][ T0] Detected VIPT I-cache on CPU0 [ 0.000000][ T0] CPU features: detected: GIC system register CPU interface [ 0.000000][ T0] CPU features: detected: Virtualization Host Extensions [ 0.000000][ T0] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000][ T0] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000][ T0] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 1286807, 2441009 [ 0.000000][ T0] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000][ T0] alternatives: patching kernel code [ 0.000000][ T0] Fallback order for Node 0: 0 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 516096 [ 0.000000][ T0] Policy zone: DMA [ 0.000000][ T0] Kernel command line: BOOT_IMAGE=/boot/aarch64/linux earlycon console=ttyLP0,115200 cpuidle.off=1 maxcput[ 0.000000][ T0] Unknown kernel command line parameters "BOOT_IMAGE=/boot/aarch64/linux linemode=1", will be passed to u.[ 0.000000][ T0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000][ T0] Memory: 130944K/2097152K available (14784K kernel code, 3368K rwdata, 11456K rodata, 6848K init, 1870K )[ 0.000000][ T0] random: get_random_u64 called from __kmem_cache_create+0x34/0x540 with crng_init=0 [ 0.000000][ T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000][ T0] ftrace: allocating 45922 entries in 180 pages [ 0.000000][ T0] ftrace: allocated 180 pages with 4 groups [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] Dynamic Preempt: none [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU event tracing is enabled. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=768 to nr_cpu_ids=2. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Rude variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000][ T0] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000][ T0] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000][ T0] GICv3: 960 SPIs implemented [ 0.000000][ T0] GICv3: 0 Extended SPIs implemented [ 0.000000][ T0] GICv3: Distributor has no Range Selector support [ 0.000000][ T0] Root IRQ handler: gic_handle_irq [ 0.000000][ T0] GICv3: 16 PPIs implemented [ 0.000000][ T0] GICv3: CPU0: found redistributor 0 region 0:0x0000000048040000 [ 0.000000][ T0] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000][ T0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 44079520259s[ 0.000000][ T0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.009325][ T0] Console: colour dummy device 80x25 [ 0.014255][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.025211][ T0] pid_max: default: 32768 minimum: 301 [ 0.030548][ T0] LSM: Security Framework initializing [ 0.035869][ T0] AppArmor: AppArmor initialized [ 0.040607][ T0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.048611][ T0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.058396][ T1] rcu: Hierarchical SRCU implementation. [ 0.065040][ T1] Remapping and enabling EFI services. [ 0.070468][ T1] smp: Bringing up secondary CPUs ... [ 0.075475][ T1] smp: Brought up 1 node, 1 CPU [ 0.080112][ T1] SMP: Total of 1 processors activated. [ 0.085499][ T1] CPU features: detected: 32-bit EL0 Support [ 0.091292][ T1] CPU features: detected: 32-bit EL1 Support [ 0.097106][ T1] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.106372][ T1] CPU features: detected: Common not Private translations [ 0.113310][ T1] CPU features: detected: CRC32 instructions [ 0.119112][ T1] CPU features: detected: Data cache clean to Point of Persistence [ 0.126831][ T1] CPU features: detected: RCpc load-acquire (LDAPR) [ 0.133239][ T1] CPU features: detected: LSE atomic instructions [ 0.139483][ T1] CPU features: detected: Privileged Access Never [ 0.145719][ T1] CPU features: detected: RAS Extension Support [ 0.151791][ T1] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.168209][ T1] CPU: All CPU(s) started at EL2 [ 0.188234][ T17] node 0 deferred pages initialised in 10ms [ 0.194768][ T1] devtmpfs: initialized [ 0.203034][ T1] Registered cp15_barrier emulation handler [ 0.208569][ T1] Registered setend emulation handler [ 0.213723][ T1] KASLR disabled due to lack of seed [ 0.218983][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.229337][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.243524][ T1] pinctrl core: initialized pinctrl subsystem [ 0.250019][ T1] SMBIOS 3.0 present. [ 0.253604][ T1] DMI: Unknown Unknown Product/Unknown Product, BIOS 2023.04-00024-g5759fda62b3 04/01/2023 [ 0.263892][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.271001][ T1] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.278642][ T1] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.286982][ T1] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.295540][ T1] audit: initializing netlink subsys (disabled) [ 0.302513][ T1] thermal_sys: Registered thermal governor 'fair_share' [ 0.302522][ T1] thermal_sys: Registered thermal governor 'bang_bang' [ 0.309071][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.315707][ T1] thermal_sys: Registered thermal governor 'user_space' [ 0.322664][ T1] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.336677][ T21] audit: type=2000 audit(0.240:1): state=initialized audit_enabled=0 res=1 [ 0.345080][ T1] ASID allocator initialised with 32768 entries [ 0.351923][ T1] Serial: AMBA PL011 UART driver [ 0.370213][ T1] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.377390][ T1] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.384711][ T1] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.392085][ T1] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.608803][ T1] ACPI: Interpreter disabled. [ 0.613654][ T1] iommu: Default domain type: Passthrough [ 0.619343][ T1] pps_core: LinuxPPS API ver. 1 registered [ 0.624833][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.634545][ T1] PTP clock support registered [ 0.639242][ T1] EDAC MC: Ver: 3.0.0 [ 0.643659][ T1] Registered efivars operations [ 0.648384][ T1] ima: secureboot mode disabled [ 0.653679][ T1] NetLabel: Initializing [ 0.657512][ T1] NetLabel: domain hash size = 128 [ 0.662538][ T1] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.668965][ T1] NetLabel: unlabeled traffic allowed by default [ 0.681433][ T1] vgaarb: loaded [ 0.684873][ T1] clocksource: Switched to clocksource arch_sys_counter [ 0.719244][ T1] VFS: Disk quotas dquot_6.6.0 [ 0.723648][ T1] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.731608][ T1] AppArmor: AppArmor Filesystem Enabled [ 0.736824][ T1] pnp: PnP ACPI: disabled [ 0.758643][ T1] NET: Registered PF_INET protocol family [ 0.764075][ T1] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.772842][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.781841][ T1] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.790454][ T1] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 0.798542][ T1] TCP: Hash tables configured (established 16384 bind 16384) [ 0.805720][ T1] MPTCP token hash table entries: 2048 (order: 3, 49152 bytes, linear) [ 0.813646][ T1] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.821004][ T1] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.828916][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.835123][ T1] NET: Registered PF_XDP protocol family [ 0.840557][ T1] PCI: CLS 0 bytes, default 64 [ 0.845539][ T57] Trying to unpack rootfs image as initramfs... [ 0.945430][ T1] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available [ 0.954278][ T1] kvm [1]: IPA Size Limit: 40 bits [ 0.959038][ T1] kvm [1]: GICv3: no GICV resource entry [ 0.964434][ T1] kvm [1]: disabling GICv2 emulation [ 0.969562][ T1] kvm [1]: GIC system register CPU interface enabled [ 1.005456][ T1] kvm [1]: vgic interrupt IRQ9 [ 1.009925][ T1] kvm [1]: VHE mode initialized successfully [ 1.026091][ T1] Initialise system trusted keyrings [ 1.030993][ T1] Key type blacklist registered [ 1.045044][ T1] workingset: timestamp_bits=40 max_order=19 bucket_order=0 [ 1.055951][ T1] zbud: loaded [ 1.075908][ T1] integrity: Platform Keyring initialized [ 4.419726][ T1] Key type asymmetric registered [ 4.424264][ T1] Asymmetric key parser 'x509' registered [ 4.429999][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 4.455166][ T1] io scheduler mq-deadline registered [ 4.460135][ T1] io scheduler kyber registered [ 4.464980][ T1] io scheduler bfq registered [ 4.487688][ T1] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 4.525336][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 4.533899][ T1] Serial: AMBA driver [ 4.537857][ T1] msm_serial: driver initialized [ 4.555810][ T16] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 4.563420][ T1] libphy: Fixed MDIO Bus: probed [ 4.575268][ T1] mousedev: PS/2 mouse device common for all mice [ 4.583197][ T1] failed to register cpuidle driver [ 4.605025][ T1] ledtrig-cpu: registered to indicate activity on CPUs [ 4.612441][ T1] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 4.619604][ T1] hid: raw HID events driver (C) Jiri Kosina [ 6.734635][ T57] Freeing initrd memory: 175364K [ 6.744339][ T1] drop_monitor: Initializing network drop monitor service [ 6.783998][ T1] NET: Registered PF_INET6 protocol family [ 6.799716][ T1] Segment Routing with IPv6 [ 6.803818][ T1] RPL Segment Routing with IPv6 [ 6.809250][ T1] registered taskstats version 1 [ 6.813946][ T1] Loading compiled-in X.509 certificates [ 6.819400][ T1] Loaded X.509 cert 'SUSE Linux Enterprise Secure Boot Signkey: a746b64b6cb71f13385638055f46162bac632acd' [ 6.830577][ T1] zswap: loaded using pool lzo/zbud [ 6.835569][ T1] page_owner is disabled [ 6.839658][ T1] Key type ._fscrypt registered [ 6.844116][ T1] Key type .fscrypt registered [ 6.848742][ T1] Key type fscrypt-provisioning registered [ 6.863920][ T1] Key type encrypted registered [ 6.868425][ T1] AppArmor: AppArmor sha1 policy hashing enabled [ 6.874669][ T1] ima: No TPM chip found, activating TPM-bypass! [ 6.880733][ T1] Loading compiled-in module X.509 certificates [ 6.886835][ T1] Loaded X.509 cert 'SUSE Linux Enterprise Secure Boot Signkey: a746b64b6cb71f13385638055f46162bac632acd' [ 6.897847][ T1] ima: Allocated hash algorithm: sha256 [ 6.903240][ T1] ima: No architecture policies found [ 6.908469][ T1] evm: Initialising EVM extended attributes: [ 6.914212][ T1] evm: security.selinux [ 6.918206][ T1] evm: security.SMACK64 (disabled) [ 6.923138][ T1] evm: security.SMACK64EXEC (disabled) [ 6.928435][ T1] evm: security.SMACK64TRANSMUTE (disabled) [ 6.934145][ T1] evm: security.SMACK64MMAP (disabled) [ 6.939436][ T1] evm: security.apparmor [ 6.943505][ T1] evm: security.ima [ 6.947149][ T1] evm: security.capability [ 6.951392][ T1] evm: HMAC attrs: 0x1 [ 6.958372][ T1] clk: Not disabling unused clocks [ 6.963132][ T1] Warning: unable to open an initial console. [ 6.974951][ T1] Freeing unused kernel memory: 6848K [ 7.004902][ T1] Run /init as init process [ 7.131685][ T108] zram: Added device: zram0 [ 7.251012][ T107] zram0: detected capacity change from 0 to 2097152 [ 11.285387][ T1] EXT4-fs (zram0): mounting ext2 file system using the ext4 subsystem [ 11.294201][ T1] EXT4-fs (zram0): mounted filesystem without journal. Opts: (null). Quota mode: none. [ 13.597289][ T121] loop: module loaded [ 14.070672][ T149] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 14.581382][ T1] loop0: detected capacity change from 0 to 290688 [ 15.546253][ T1] loop1: detected capacity change from 0 to 30976 [ 16.030314][ T182] SCSI subsystem initialized [ 16.038597][ T182] alua: device handler registered [ 16.082812][ T184] emc: device handler registered [ 16.184775][ T185] rdac: device handler registered [ 19.633386][ T197] usbcore: registered new interface driver usbfs [ 19.639478][ T197] usbcore: registered new interface driver hub [ 19.645355][ T197] usbcore: registered new device driver usb [ 19.731518][ T198] sdhci: Secure Digital Host Controller Interface driver [ 19.738208][ T198] sdhci: Copyright(c) Pierre Ossman [ 19.789481][ T201] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 20.042876][ T204] sdhci-pltfm: SDHCI platform and OF driver helper [ 20.134009][ T195] cryptd: max_cpu_qlen set to 1000 [ 23.689491][ T414] RPC: Registered named UNIX socket transport module. [ 23.695891][ T414] RPC: Registered udp transport module. [ 23.701224][ T414] RPC: Registered tcp transport module. [ 23.706604][ T414] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 24.098915][ T418] random: dbus-uuidgen: uninitialized urandom read (12 bytes read) [ 24.106532][ T418] random: dbus-uuidgen: uninitialized urandom read (8 bytes read) [ 24.557109][ T419] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 25.640377][ T423] urandom_read_iter: 2 callbacks suppressed ==> Stuck here.
(In reply to Peng Fan from comment #0) > > ==> Stuck here. Usually this means that some important module(s) is/are missing from initrd. You could add this [1] to linux command line (via Grub2 configuration menuentry) to narrow down where it stuck. Please attach log files. [1] linuxrc.log=/dev/console linemode=1 linuxrc.debug=1 [2] https://en.opensuse.org/SDB:Linuxrc
[ 5.106154][ T1] evm: HMAC attrs: 0x1 [ 5.113013][ T1] Warning: unable to open an initial console. [ 5.124652][ T1] Freeing unused kernel memory: 6848K [ 5.166306][ T1] Run /init as init process Not able to open console. I shared with Matthias in private email that CLK_IMX93 and PINCTRL_IMX93 is not built in. After the two options are built in, the LPUART console should work and we could see more on future log if still has issue.
now part of 15.6 Kernel of the Day: https://github.com/SUSE/kernel-source/commit/09c889add551ec0e2a1866340a5bf3f8f6fa4712 You will need to wait for a new beta version gets available, otherwise we can pass information on how to update the kernel on the installer to test. Also merged to master and stable. Closing for now.