Bugzilla – Bug 170097
Promise SATA 300-TX2 plus does not see any SATA disk
Last modified: 2007-01-08 16:56:25 UTC
The Controller Promise SATA 300-TX2 plus does not see any SATA disk.
Do you have any kernel log files you can attach to show us what the controller is trying to do? Is this on the install, or after you boot normally after install has finished?
Wenn I try whith other distribution like ubuntu or knoppix, the controller works fine. SUSE does not see the SATA Disk on install and after I boot normally.
Any kernel log or installer logs you can provide us? Without that, it's going to be very hard to work on this.
No logs for two weeks, alas, I'll have to close this bugzilla. Please re-open if the problem persists with the latest version and attach the requested logfiles.
In the new Version OpenSuse 10.2 the Bug is still there. Can you help me, where can I find the requestet log?
libata version 1.20 loaded. sata_promise 0000:02:0a.0: version 1.03 ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 169 ata1: SATA max UDMA/133 cmd 0xE081A200 ctl 0xE081A238 bmdma 0x0 irq 169 ata2: SATA max UDMA/133 cmd 0xE081A280 ctl 0xE081A2B8 bmdma 0x0 irq 169 ata1: SATA link down (SStatus 0) scsi0 : sata_promise ata2: SATA link down (SStatus 0) scsi1 : sata_promise lsmod shows sata_promise 10500 0 libata 65168 1 sata_promise piix 9092 0 [permanent] sd_mod 16144 0 scsi_mod 121992 3 sata_promise,libata,sd_mod
On openSUSE 10.2 Alpha4 still it does not work. Here some information : uname -r 2.6.18-rc5-git6-2-default lspci 00:00.0 Host bridge: Intel Corporation 82845 845 (Brookdale) Chipset Host Bridge (rev 03) 00:01.0 PCI bridge: Intel Corporation 82845 845 (Brookdale) Chipset AGP Bridge (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 12) 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 12) 00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 12) 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 12) 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 12) 00:1f.4 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #2) (rev 12) 00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 12) 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400/G450 (rev 82) 02:08.0 Ethernet controller: Intel Corporation 82801BA/BAM/CA/CAM Ethernet Controller (rev 03) 02:0a.0 Mass storage controller: Promise Technology, Inc. PDC40775 (SATA 300 TX2plus) (rev 02) dmesg | grep sata sata_promise 0000:02:0a.0: version 1.04 scsi0 : sata_promise scsi1 : sata_promise lsmod Module Size Used by parport_pc 41956 0 parport 39752 1 parport_pc acpi_cpufreq 11524 0 freq_table 8832 1 acpi_cpufreq af_packet 29320 0 iptable_filter 7168 0 ip_tables 17604 1 iptable_filter x_tables 18180 1 ip_tables joydev 13504 0 sg 37916 0 st 40860 0 sr_mod 20132 0 ipv6 263712 14 asus_acpi 21148 0 button 10896 0 battery 14340 0 ac 9476 0 apparmor 60312 0 aamatch_pcre 18432 1 apparmor loop 20360 0 dm_mod 60184 0 shpchp 40224 0 pci_hotplug 35392 1 shpchp intel_rng 7040 0 i8xx_tco 11160 0 uhci_hcd 27276 0 intel_agp 26652 1 usbcore 128260 2 uhci_hcd agpgart 35528 1 intel_agp i2c_i801 11660 0 i2c_core 25216 1 i2c_i801 matrox_w1 8192 0 e100 39688 0 ide_cd 42272 0 wire 27652 1 matrox_w1 mii 9600 1 e100 cdrom 38432 2 sr_mod,ide_cd reiserfs 237312 2 edd 13892 0 fan 8964 0 sata_promise 16004 0 libata 101652 1 sata_promise piix 13700 0 [permanent] thermal 18568 0 processor 34664 2 acpi_cpufreq,thermal sd_mod 24576 0 scsi_mod 136712 5 sg,st,sr_mod,libata,sd_mod ide_disk 20480 4 ide_core 130632 3 ide_cd,piix,ide_disk fdisk -l Disk /dev/hda: 40.0 GB, 40037760000 bytes 255 heads, 63 sectors/track, 4867 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 1 128 1028128+ 82 Linux swap / Solaris /dev/hda2 * 129 2024 15229620 83 Linux /dev/hda3 2025 4867 22836397+ 83 Linux If You need more, tell me.
The Promise SATA 300-TX2 plus does still not work together with openSUSE 10.2 Alpha5. (But nobody cares about this.) If I can help, tell me please.
Stephan, does booting with acpi=off help? Sometimes it does.
Hi Lars, acpi=off does regrettably not help. Why does knoppix an ubuntu work without any problem?
Hi Stephan, I have the same card (at least same controller) and it works fine under SL 10.1 and openSUSE alpha4. I'm quite sure, that this bug muste be related to your hardware. Maybe you have a problem with other devices. Try to unmount as many PCI-devices as possible, remove them from your computer, then reboot.
Why does knoppix an ubuntu work without any problem?
I don't know, what kernel version are they based off of? And do they provide any kernel patches for your hardware in the kernel?
Kubuntu kernel 2.6.15-20 Knoppix kernel 2.6.17 How can I test for You, if they provide any kernel patches?
Stephan: please do the following: attach a disk to the card, switch the disk on ;-) open a console with tail -f /var/log/messages open a second console and unload the sata_promise module: rmmod sata_promise then reload the module: modprobe sata_promise Post all messages here, which appear meanwhile in the first console.
You mean with openSUSE 10.2 Alpha5 : tail -f /var/log/messages Oct 15 18:54:40 dhcppc1 su: (to root) blacky on /dev/pts/1 Oct 15 18:56:08 dhcppc1 kernel: sata_promise 0000:02:0a.0: version 1.04 Oct 15 18:56:08 dhcppc1 syslog-ng[2085]: Changing permissions on special file /dev/xconsole Oct 15 18:56:08 dhcppc1 syslog-ng[2085]: Changing permissions on special file /dev/tty10 Oct 15 18:56:08 dhcppc1 kernel: PCI: Enabling device 0000:02:0a.0 (0110 -> 0113) Oct 15 18:56:08 dhcppc1 kernel: ata5: SATA max UDMA/133 cmd 0xE083C200 ctl 0xE083C238 bmdma 0x0 irq 201 Oct 15 18:56:08 dhcppc1 kernel: ata6: SATA max UDMA/133 cmd 0xE083C280 ctl 0xE083C2B8 bmdma 0x0 irq 201 Oct 15 18:56:08 dhcppc1 kernel: scsi4 : sata_promise Oct 15 18:56:08 dhcppc1 kernel: ata5: SATA link down (SStatus 0 SControl 300) Oct 15 18:56:08 dhcppc1 kernel: scsi5 : sata_promise Oct 15 18:56:08 dhcppc1 kernel: ata6: SATA link down (SStatus 0 SControl 300) I hope this helps
Hello, Stephan Schwarz. Can you please post dmesg of a successful boot from ubuntu or knoppix? Sorry about all the trouble. :-)
ubuntu@ubuntu:~$ dmesg [4294667.296000] Linux version 2.6.15-20-386 (buildd@vernadsky) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu3)) #1 PREEMPT Tue Apr 4 17:48:51 UTC 2006 [4294667.296000] BIOS-provided physical RAM map: [4294667.296000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [4294667.296000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [4294667.296000] BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved) [4294667.296000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [4294667.296000] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) [4294667.296000] BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data) [4294667.296000] BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS) [4294667.296000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [4294667.296000] 0MB HIGHMEM available. [4294667.296000] 511MB LOWMEM available. [4294667.296000] found SMP MP-table at 000fb6b0 [4294667.296000] On node 0 totalpages: 131056 [4294667.296000] DMA zone: 4096 pages, LIFO batch:0 [4294667.296000] DMA32 zone: 0 pages, LIFO batch:0 [4294667.296000] Normal zone: 126960 pages, LIFO batch:31 [4294667.296000] HighMem zone: 0 pages, LIFO batch:0 [4294667.296000] DMI 2.3 present. [4294667.296000] ACPI: RSDP (v000 AMI ) @ 0x000f9e10 [4294667.296000] ACPI: RSDT (v001 HP-BDD HPBDD-JA 0x00000010 MSFT 0x00000097) @ 0x1fff0000 [4294667.296000] ACPI: FADT (v001 HP-BDD HPBDD-JA 0x00000001 MSFT 0x00000097) @ 0x1fff0030 [4294667.296000] ACPI: MADT (v001 HP-BDD 0x00000009 MSFT 0x00000097) @ 0x1fff00e0 [4294667.296000] ACPI: BOOT (v001 HP-BDD INTEL845 0x00000009 MSFT 0x00000097) @ 0x1fff00b0 [4294667.296000] ACPI: DSDT (v001 INTEL BROKDALE 0x00001014 MSFT 0x0100000d) @ 0x00000000 [4294667.296000] ACPI: PM-Timer IO Port: 0x808 [4294667.296000] ACPI: Local APIC address 0xfee00000 [4294667.296000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [4294667.296000] Processor #0 15:1 APIC version 20 [4294667.296000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [4294667.296000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [4294667.296000] ACPI: IRQ0 used by override. [4294667.296000] ACPI: IRQ2 used by override. [4294667.296000] ACPI: IRQ9 used by override. [4294667.296000] Enabling APIC mode: Flat. Using 1 I/O APICs [4294667.296000] Using ACPI (MADT) for SMP configuration information [4294667.296000] Allocating PCI resources starting at 30000000 (gap: 20000000:dff00000) [4294667.296000] Built 1 zonelists [4294667.296000] Kernel command line: BOOT_IMAGE=/install/vmlinuz boot=casper initrd=/install/initrd.gz ramdisk_size=1048576 root=/dev/ram rw quiet splash -- [4294667.296000] mapped APIC to ffffd000 (fee00000) [4294667.296000] mapped IOAPIC to ffffc000 (fec00000) [4294667.296000] Initializing CPU#0 [4294667.296000] PID hash table entries: 2048 (order: 11, 32768 bytes) [4294667.296000] Detected 1893.702 MHz processor. [4294667.296000] Using pmtmr for high-res timesource [4294667.296000] Console: colour VGA+ 80x25 [4294669.774000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [4294669.776000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [4294669.799000] Memory: 508584k/524224k available (1973k kernel code, 14984k reserved, 601k data, 288k init, 0k highmem) [4294669.799000] Checking if this processor honours the WP bit even in supervisor mode... Ok. [4294669.859000] Calibrating delay using timer specific routine.. 3788.75 BogoMIPS (lpj=1894379) [4294669.859000] Security Framework v1.0.0 initialized [4294669.859000] SELinux: Disabled at boot. [4294669.859000] Mount-cache hash table entries: 512 [4294669.859000] CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000 [4294669.859000] CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000 [4294669.859000] CPU: Trace cache: 12K uops, L1 D cache: 8K [4294669.859000] CPU: L2 cache: 256K [4294669.859000] CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 00000000 00000000 00000000 [4294669.859000] mtrr: v2.0 (20020519) [4294669.859000] CPU: Intel(R) Pentium(R) 4 CPU 1.90GHz stepping 02 [4294669.859000] Enabling fast FPU save and restore... done. [4294669.859000] Enabling unmasked SIMD FPU exception support... done. [4294669.859000] Checking 'hlt' instruction... OK. [4294669.863000] checking if image is initramfs... it is [4294670.668000] Freeing initrd memory: 6785k freed [4294670.709000] ACPI: Looking for DSDT ... not found! [4294670.712000] ENABLING IO-APIC IRQs [4294670.712000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [4294670.823000] NET: Registered protocol family 16 [4294670.823000] EISA bus registered [4294670.823000] ACPI: bus type pci registered [4294670.847000] PCI: PCI BIOS revision 2.10 entry at 0xfdab1, last bus=2 [4294670.847000] PCI: Using configuration type 1 [4294670.848000] ACPI: Subsystem revision 20051216 [4294670.872000] ACPI: Interpreter enabled [4294670.872000] ACPI: Using IOAPIC for interrupt routing [4294670.873000] ACPI: PCI Root Bridge [PCI0] (0000:00) [4294670.873000] PCI: Probing PCI hardware (bus 00) [4294670.876000] PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO [4294670.876000] PCI quirk: region 0400-043f claimed by ICH4 GPIO [4294670.877000] Boot video device is 0000:01:00.0 [4294670.877000] PCI: Transparent bridge - 0000:00:1e.0 [4294670.877000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [4294670.880000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT] [4294670.885000] ACPI: Power Resource [URP1] (off) [4294670.885000] ACPI: Power Resource [URP2] (off) [4294670.885000] ACPI: Power Resource [FDDP] (off) [4294670.886000] ACPI: Power Resource [LPTP] (off) [4294670.887000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [4294670.887000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) [4294670.887000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. [4294670.888000] ACPI: PCI Interrupt Link [LNKD] (IRQs *9) [4294670.888000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [4294670.888000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. [4294670.889000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [4294670.889000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [4294670.889000] Linux Plug and Play Support v0.97 (c) Adam Belay [4294670.889000] pnp: PnP ACPI init [4294670.895000] pnp: PnP ACPI: found 11 devices [4294670.895000] PnPBIOS: Disabled by ACPI PNP [4294670.895000] PCI: Using ACPI for IRQ routing [4294670.895000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [4294670.899000] PCI: Bridge: 0000:00:01.0 [4294670.899000] IO window: disabled. [4294670.899000] MEM window: ded00000-dfdfffff [4294670.899000] PREFETCH window: daa00000-deafffff [4294670.899000] PCI: Bridge: 0000:00:1e.0 [4294670.899000] IO window: 9000-afff [4294670.899000] MEM window: dfe00000-dfefffff [4294670.899000] PREFETCH window: deb00000-debfffff [4294670.899000] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [4294670.899000] Simple Boot Flag at 0x79 set to 0x1 [4294670.900000] audit: initializing netlink socket (disabled) [4294670.900000] audit(1162940379.899:1): initialized [4294670.900000] VFS: Disk quotas dquot_6.5.1 [4294670.900000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [4294670.900000] Initializing Cryptographic API [4294670.900000] io scheduler noop registered [4294670.900000] io scheduler anticipatory registered [4294670.900000] io scheduler deadline registered [4294670.900000] io scheduler cfq registered [4294670.900000] isapnp: Scanning for PnP cards... [4294671.257000] isapnp: No Plug & Play device found [4294671.281000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [4294671.283000] serio: i8042 AUX port at 0x60,0x64 irq 12 [4294671.284000] serio: i8042 KBD port at 0x60,0x64 irq 1 [4294671.284000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled [4294671.284000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [4294671.284000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [4294671.288000] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [4294671.288000] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [4294671.289000] RAMDISK driver initialized: 16 RAM disks of 1048576K size 1024 blocksize [4294671.289000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [4294671.289000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [4294671.289000] ACPI: bus type ide registered [4294671.289000] mice: PS/2 mouse device common for all mice [4294671.290000] EISA: Probing bus 0 at eisa.0 [4294671.290000] EISA: Detected 0 cards. [4294671.290000] NET: Registered protocol family 2 [4294671.300000] IP route cache hash table entries: 8192 (order: 3, 32768 bytes) [4294671.300000] TCP established hash table entries: 32768 (order: 5, 131072 bytes) [4294671.300000] TCP bind hash table entries: 32768 (order: 5, 131072 bytes) [4294671.300000] TCP: Hash tables configured (established 32768 bind 32768) [4294671.300000] TCP reno registered [4294671.301000] TCP bic registered [4294671.301000] NET: Registered protocol family 1 [4294671.301000] NET: Registered protocol family 8 [4294671.301000] NET: Registered protocol family 20 [4294671.301000] Using IPI Shortcut mode [4294671.301000] ACPI wakeup devices: [4294671.301000] ICHB PS2K UAR1 UAR2 USB1 USB2 SLPB [4294671.301000] ACPI: (supports S0 S1 S3 S4 S5) [4294671.301000] Freeing unused kernel memory: 288k freed [4294671.313000] input: AT Translated Set 2 keyboard as /class/input/input0 [4294671.408000] vga16fb: initializing [4294671.408000] vga16fb: mapped to 0xc00a0000 [4294671.468000] Console: switching to colour frame buffer device 80x25 [4294671.468000] fb0: VGA16 VGA frame buffer device [4294672.618000] Capability LSM initialized [4294672.681000] ACPI: Processor [CPU1] (supports 8 throttling states) [4294673.766000] SCSI subsystem initialized [4294673.768000] libata version 1.20 loaded. [4294673.771000] sata_promise 0000:02:0a.0: version 1.03 [4294673.771000] ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 169 [4294673.772000] sata_promise PATA port found [4294673.783000] ata1: SATA max UDMA/133 cmd 0xE0822200 ctl 0xE0822238 bmdma 0x0 irq 169 [4294673.783000] ata2: SATA max UDMA/133 cmd 0xE0822280 ctl 0xE08222B8 bmdma 0x0 irq 169 [4294673.783000] ata3: PATA max UDMA/133 cmd 0xE0822300 ctl 0xE0822338 bmdma 0x0 irq 169 [4294674.138000] ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4773 85:7c69 86:3e01 87:4763 88:407f [4294674.138000] ata1: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48 [4294674.139000] ata1: dev 0 configured for UDMA/133 [4294674.139000] scsi0 : sata_promise [4294674.340000] ata2: no device found (phy stat 00000000) [4294674.340000] scsi1 : sata_promise [4294674.502000] ATA: abnormal status 0x8 on port 0xE082231C [4294674.502000] ata3: disabling port [4294674.502000] scsi2 : sata_promise [4294674.503000] Vendor: ATA Model: Maxtor 7V300F0 Rev: VA11 [4294674.503000] Type: Direct-Access ANSI SCSI revision: 05 [4294674.517000] SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) [4294674.517000] SCSI device sda: drive cache: write back [4294674.524000] SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) [4294674.524000] SCSI device sda: drive cache: write back [4294674.524000] sda: sda1 [4294674.552000] sd 0:0:0:0: Attached scsi disk sda [4294674.703000] ICH2: IDE controller at PCI slot 0000:00:1f.1 [4294674.703000] ICH2: chipset revision 18 [4294674.703000] ICH2: not 100% native mode: will probe irqs later [4294674.703000] ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio [4294674.703000] ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio [4294674.703000] Probing IDE interface ide0... [4294674.967000] hda: ST340016A, ATA DISK drive [4294675.579000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [4294675.579000] Probing IDE interface ide1... [4294676.251000] hdc: SAMSUNG DVD-ROM SD-616T, ATAPI CD/DVD-ROM drive [4294676.557000] ide1 at 0x170-0x177,0x376 on irq 15 [4294676.568000] hda: max request size: 128KiB [4294676.582000] hda: 78198750 sectors (40037 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) [4294676.582000] hda: cache flushes not supported [4294676.582000] hda: hda1 hda2 hda3 [4294676.616000] hdc: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33) [4294676.616000] Uniform CD-ROM driver Revision: 3.20 [4294676.857000] usbcore: registered new driver usbfs [4294676.857000] usbcore: registered new driver hub [4294676.860000] USB Universal Host Controller Interface driver v2.3 [4294676.861000] ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 177 [4294676.861000] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [4294676.861000] uhci_hcd 0000:00:1f.2: UHCI Host Controller [4294676.862000] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1 [4294676.862000] uhci_hcd 0000:00:1f.2: irq 177, io base 0x0000d000 [4294676.863000] hub 1-0:1.0: USB hub found [4294676.863000] hub 1-0:1.0: 2 ports detected [4294676.964000] ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 185 [4294676.964000] PCI: Setting latency timer of device 0000:00:1f.4 to 64 [4294676.964000] uhci_hcd 0000:00:1f.4: UHCI Host Controller [4294676.964000] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2 [4294676.964000] uhci_hcd 0000:00:1f.4: irq 185, io base 0x0000d400 [4294676.965000] hub 2-0:1.0: USB hub found [4294676.965000] hub 2-0:1.0: 2 ports detected [4294687.185000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error } [4294687.185000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 } [4294687.185000] ide: failed opcode was: unknown [4294687.185000] end_request: I/O error, dev hdc, sector 1344544 [4294687.185000] Buffer I/O error on device hdc, logical block 168068 [4294696.125000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error } [4294696.125000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 } [4294696.125000] ide: failed opcode was: unknown [4294696.125000] end_request: I/O error, dev hdc, sector 1344544 [4294696.125000] Buffer I/O error on device hdc, logical block 168068 [4294705.065000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error } [4294705.065000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 } [4294705.065000] ide: failed opcode was: unknown [4294705.065000] end_request: I/O error, dev hdc, sector 1344544 [4294705.065000] Buffer I/O error on device hdc, logical block 168068 [4294714.005000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error } [4294714.005000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 } [4294714.005000] ide: failed opcode was: unknown [4294714.005000] end_request: I/O error, dev hdc, sector 1344544 [4294714.005000] Buffer I/O error on device hdc, logical block 168068 [4294722.945000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error } [4294722.945000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 } [4294722.945000] ide: failed opcode was: unknown [4294722.945000] end_request: I/O error, dev hdc, sector 1344544 [4294722.945000] Buffer I/O error on device hdc, logical block 168068 [4294731.885000] hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error } [4294731.885000] hdc: media error (bad sector): error=0x30 { LastFailedSense=0x03 } [4294731.885000] ide: failed opcode was: unknown [4294731.885000] end_request: I/O error, dev hdc, sector 1344544 [4294731.885000] Buffer I/O error on device hdc, logical block 168068 [4294734.796000] ISO 9660 Extensions: Microsoft Joliet Level 3 [4294734.840000] ISO 9660 Extensions: RRIP_1991A [4294734.894000] loop: loaded (max 8 devices) [4294734.916000] Registering unionfs 1.1.2 [4294735.020000] squashfs: version 3.0prerelease (2006/1/24) Phillip Lougher [4294775.052000] e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI [4294775.052000] e100: Copyright(c) 1999-2005 Intel Corporation [4294775.053000] ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 193 [4294775.077000] e100: eth0: e100_probe: addr 0xdfefe000, irq 193, MAC addr 00:04:23:22:B4:58 [4294783.705000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [4294783.991000] e100: eth0: e100_watchdog: link up, 100Mbps, half-duplex [4294785.073000] NET: Registered protocol family 17 [4294785.631000] NET: Registered protocol family 10 [4294785.631000] lo: Disabled Privacy Extensions [4294785.631000] IPv6 over IPv4 tunneling driver [4294786.107000] Linux agpgart interface v0.101 (c) Dave Jones [4294786.134000] agpgart: Detected an Intel i845 Chipset. [4294786.138000] agpgart: AGP aperture is 64M @ 0xe0000000 [4294786.293000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [4294786.320000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [4294786.822000] input: PC Speaker as /class/input/input1 [4294787.035000] Real Time Clock Driver v1.12 [4294787.077000] logips2pp: Detected unknown logitech mouse model 89 [4294787.122000] Driver for 1-wire Dallas network protocol. [4294787.137000] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2 [4294787.321000] hw_random hardware driver 1.0.0 loaded [4294787.393000] matrox_w1 0000:01:00.0: Matrox G400 GPIO transport layer for 1-wire. [4294787.504000] Floppy drive(s): fd0 is 1.44M [4294787.571000] FDC 0 is a National Semiconductor PC87306 [4294787.824000] parport: PnPBIOS parport detected. [4294787.824000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] [4294787.907000] ts: Compaq touchscreen protocol output [4294788.487000] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201 [4294788.487000] PCI: Setting latency timer of device 0000:00:1f.5 to 64 [4294788.798000] intel8x0_measure_ac97_clock: measured 50820 usecs [4294788.798000] intel8x0: clocking to 48000 [4294790.240000] Adding 1028120k swap on /dev/hda1. Priority:-1 extents:1 across:1028120k [4294790.597000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 [4294790.597000] md: bitmap version 4.39 [4294791.265000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com [4294795.788000] eth0: no IPv6 routers present [4294798.076000] ACPI: Power Button (FF) [PWRF] [4294798.076000] ACPI: Power Button (CM) [PWRB] [4294798.076000] ACPI: Sleep Button (CM) [SLPB] [4294798.240000] ibm_acpi: ec object not found [4294798.276000] pcc_acpi: loading... [4294804.972000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [4294804.972000] apm: overridden by ACPI. [4294809.477000] hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error } [4294809.477000] hdc: drive_cmd: error=0x04 { AbortedCommand } [4294809.477000] ide: failed opcode was: 0xec [4294809.667000] hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error } [4294809.667000] hdc: drive_cmd: error=0x04 { AbortedCommand } [4294809.667000] ide: failed opcode was: 0xec [4294810.384000] Bluetooth: Core ver 2.8 [4294810.384000] NET: Registered protocol family 31 [4294810.384000] Bluetooth: HCI device and connection manager initialized [4294810.384000] Bluetooth: HCI socket layer initialized [4294810.525000] Bluetooth: L2CAP ver 2.8 [4294810.525000] Bluetooth: L2CAP socket layer initialized [4294810.746000] Bluetooth: RFCOMM socket layer initialized [4294810.746000] Bluetooth: RFCOMM TTY layer initialized [4294810.746000] Bluetooth: RFCOMM ver 1.7 [4294816.642000] [drm] Initialized drm 1.0.0 20040925 [4294816.750000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 209 [4294816.751000] [drm] Initialized mga 3.2.0 20050607 on minor 0: [4294816.753000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. [4294816.753000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode [4294816.753000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [4295020.375000] e100: eth0: e100_watchdog: link up, 100Mbps, half-duplex [4295030.996000] eth0: no IPv6 routers present
openSUSE 10.2 Beta1 linux011:~ # dmesg Linux version 2.6.18.1-8-default (geeko@buildhost) (gcc version 4.1.2 20061018 (prerelease) (SUSE Linux)) #1 SMP Fri Oct 20 12:25:45 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data) BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. found SMP MP-table at 000fb6b0 On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 126960 pages, LIFO batch:31 DMI 2.3 present. Using APIC driver default IO/L-APIC allowed because system is MP or new enough ACPI: RSDP (v000 AMI ) @ 0x000f9e10 ACPI: RSDT (v001 HP-BDD HPBDD-JA 0x00000010 MSFT 0x00000097) @ 0x1fff0000 ACPI: FADT (v001 HP-BDD HPBDD-JA 0x00000001 MSFT 0x00000097) @ 0x1fff0030 ACPI: MADT (v001 HP-BDD 0x00000009 MSFT 0x00000097) @ 0x1fff00e0 ACPI: BOOT (v001 HP-BDD INTEL845 0x00000009 MSFT 0x00000097) @ 0x1fff00b0 ACPI: DSDT (v001 INTEL BROKDALE 0x00001014 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:1 APIC version 20 ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dff00000) Detected 1893.098 MHz processor. Built 1 zonelists. Total pages: 131056 Kernel command line: root=/dev/sda2 vga=0x31a resume=/dev/sda1 splash=silent bootsplash: silent mode. mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512912k/524224k available (1700k kernel code, 10760k reserved, 677k data, 196k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3789.74 BogoMIPS (lpj=7579483) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 256K CPU: Hyper-Threading is disabled CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 16k freed checking if image is initramfs... it is Freeing initrd memory: 2907k freed ACPI: Core revision 20060707 not found! CPU0: Intel(R) Pentium(R) 4 CPU 1.90GHz stepping 02 Total of 1 processors activated (3789.74 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 Brought up 1 CPUs migration_cost=0 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfdab1, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0400-043f claimed by ICH4 GPIO Boot video device is 0000:01:00.0 PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs *9) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: ded00000-dfdfffff PREFETCH window: daa00000-deafffff PCI: Bridge: 0000:00:1e.0 IO window: 9000-afff MEM window: dfe00000-dfefffff PREFETCH window: deb00000-debfffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered Simple Boot Flag at 0x79 set to 0x1 Machine check exception polling timer started. apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1162941321.988:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) vesafb: framebuffer at 0xdc000000, mapped to 0xe0880000, using 10240k, total 16384k vesafb: mode is 1280x1024x16, linelength=2560, pages=5 vesafb: protected mode interface info at c000:77a0 vesafb: pmi: set display start = c00c7832, set palette = c00c789e vesafb: pmi: ports = 3de 3df vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 107318 bytes,<6>...found (1280x1024, 76041 bytes, v3). Console: switching to colour frame buffer device 156x60 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 input: AT Translated Set 2 keyboard as /class/input/input1 logips2pp: Detected unknown logitech mouse model 89 input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 1 Using IPI No-Shortcut mode ACPI: (supports S0 S1 S3 S4 S5) Freeing unused kernel memory: 196k freed Time: tsc clocksource has been installed. SCSI subsystem initialized ACPI: Processor [CPU1] (supports 8 throttling states) libata version 2.00 loaded. ata_piix 0000:00:1f.1: version 2.00ac6 PCI: Setting latency timer of device 0000:00:1f.1 to 64 ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xFC00 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xFC08 irq 15 scsi0 : ata_piix ata1.00: ATA-5, max UDMA/100, 78198750 sectors: LBA ata1.00: ata1: dev 0 multi count 16 ata1.00: configured for UDMA/100 ACPI Error (dsopcode-0481): Attempt to CreateField of length zero [20060707] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node dffd4ea0), AE_AML_OPERAND_VALUE ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN0.DRV0._GTF] (Node dffd4838), AE_AML_OPERAND_VALUE scsi1 : ata_piix ata2.00: ATAPI, max UDMA/33 ata2.00: configured for UDMA/33 Vendor: ATA Model: ST340016A Rev: 3.19 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 78198750 512-byte hdwr sectors (40038 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 78198750 512-byte hdwr sectors (40038 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda Vendor: SAMSUNG Model: DVD-ROM SD-616T Rev: F301 Type: CD-ROM ANSI SCSI revision: 05 sata_promise 0000:02:0a.0: version 1.04 ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 169 sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Attached scsi generic sg1 type 5 ata3: SATA max UDMA/133 cmd 0xE081A200 ctl 0xE081A238 bmdma 0x0 irq 169 ata4: SATA max UDMA/133 cmd 0xE081A280 ctl 0xE081A2B8 bmdma 0x0 irq 169 scsi2 : sata_promise sr0: scsi3-mmc drive: 1x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 ata3: SATA link down (SStatus 0 SControl 300) scsi3 : sata_promise ata4: SATA link down (SStatus 0 SControl 300) BIOS EDD facility v0.16 2004-Jun-25, 2 devices found mbcache: module not supported by Novell, setting U taint flag. Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. AppArmor: AppArmor (version 2.0-19.43r6320) initialized audit(1162941330.236:2): AppArmor (version 2.0-19.43r6320) initialized parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] lp0: using parport0 (interrupt-driven). usbcore: registered new driver usbfs usbcore: registered new driver hub i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1f.2 to 64 uhci_hcd 0000:00:1f.2: UHCI Host Controller uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1f.2: irq 177, io base 0x0000d000 usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: UHCI Host Controller usb usb1: Manufacturer: Linux 2.6.18.1-8-default uhci_hcd usb usb1: SerialNumber: 0000:00:1f.2 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Linux agpgart interface v0.101 (c) Dave Jones ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1f.4 to 64 uhci_hcd 0000:00:1f.4: UHCI Host Controller uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1f.4: irq 185, io base 0x0000d400 usb usb2: new device found, idVendor=0000, idProduct=0000 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.18.1-8-default uhci_hcd usb usb2: SerialNumber: 0000:00:1f.4 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 agpgart: Detected an Intel i845 Chipset. agpgart: AGP aperture is 64M @ 0xe0000000 ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel_rng: module not supported by Novell, setting U taint flag. Intel 82802 RNG detected intel8x0_measure_ac97_clock: measured 58792 usecs intel8x0: clocking to 48000 ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 193 wire: module not supported by Novell, setting U taint flag. Driver for 1-wire Dallas network protocol. e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 201 e100: eth0: e100_probe: addr 0xdfefe000, irq 201, MAC addr 00:04:23:22:B4:58 matrox_w1: module not supported by Novell, setting U taint flag. matrox_w1 0000:01:00.0: Matrox G400 GPIO transport layer for 1-wire. Adding 1028120k swap on /dev/sda1. Priority:-1 extents:1 across:1028120k device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com loop: loaded (max 8 devices) kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. powernow: This module only works with AMD K7 CPUs ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] e100: eth0: e100_watchdog: link up, 100Mbps, half-duplex NET: Registered protocol family 17 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver audit(1162941371.391:3): audit_pid=3792 old=0 by auid=4294967295 IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com> microcode: CPU0 updated from revision 0x3 to 0x2e, date = 05022003 ADDRCONF(NETDEV_UP): eth0: link is not ready e100: eth0: e100_watchdog: link up, 100Mbps, half-duplex ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: no IPv6 routers present
Can you please test the following patch?
Created attachment 104788 [details] use long debounce timing
Yes, I can. How do I have to do this? Now I have openSUSE 10.2 BETA2.
Sorry about being late. Please install the following kernel and post /var/log/boot.msg. Thanks. http://htj.dyndns.org/kernel-default-2.6.18.2-5.tj.debug.i586.rpm
Created attachment 106935 [details] /var/log/boot.msg
Please test the following kernel. http://htj.dyndns.org/kernel-default-2.6.18.2-33tj.i586.rpm
I get the following message: rpm -ihv kernel-default-2.6.18.2-33tj.i586.rpm error: Failed dependencies: perl-Bootloader >= 0.4.1 is needed by kernel-default-2.6.18.2-33tj.i586
The kernel is from 10.2rc1. That dependency shouldn't matter too much. Just do 'rpm --ivh --nodeps kernel-default-2.6.18.2-33tj.i586.rpm'.
Created attachment 107951 [details] /var/log/boot.msg openSUSE 10.2 RC1 still the same
I'm sorry but I'm really out of clue at this point. I've been trying to find a sata300 tx2 plus card for some time now but there doesn't seem to be any shop carrying it here. Only sata150's which work fine. I'll look again. Please be patient. Thanks.
I bought sata300 tx2 plus (105a:3d73) and openSUSE 10.2 works fine with the controller. I've tested it with various samsung, maxtor, seagate and wd hdds and also with two SATAPI ODDs (LG and plextor). Then, I downloaded knoppix 5.0.1 and diffed the kernel (it's mostly stock 2.6.17). There is no relevant change. I really wanna fix this but am stuck hard here. Where are you? Can you ship your controller and the problematic harddisk to me? I can pay you.
No response in ~20 days, and I can't reproduce the problem. Closing. Please reopen when further actions can be taken.